Can Stabilizer Jacks TJ01RT-HD be Used With Trailer Frame Running Front to Back
Updated 04/18/2024 | Published 04/11/2024
Question:
Are these camper jacks a good fit for a 2021 Geo Pro G15TB? I notice that my frame beams run front to back and not passenger to driver. So the slant on front jacks would be towards tongue jack and back jacks would be towards rear of unit. Not to the sides like on pics. Just concerned whether that makes a difference on effectiveness of such installation. Thanks for your consideration.
asked by: Carlos
(click to enlarge)
Helpful Expert Reply:
Hi Carlos; thanks for the photo and that's a smart question, but your trailer frame running front to back won't make a difference in the effectiveness of the Stabilizer Jacks # TJ01RT-HD.
They can absolutely still be used on your Geo Pro G15TB with that frame configuration to help stabilize your trailer.
Product Page this Question was Asked From
Stabilizer Jacks - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 2
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- Stabilizer Jacks
- Steel
- 0 - 1000 lbs
- Manual Jack
- 18 Inch Lift
- Bolt-On
- Weld-On
- 1 Jack
- etrailer
more information >
Continue Researching
- Shop: Stabilizer Jacks - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 2
- Video: Comprehensive Review: Stabilizer Jacks
- Video: A Closer Look at the Stabilizer Jack
- Shop: etrailer 2 Swivel Jacks w/ Bolt-On Mounting Plates - Sidewind - 10" Lift - 3,000 lbs
- Search Results: short trailer jack
- Search Results: stabilizer jacks
- Search Results: trailer jack
- Shop: etrailer Electric Trailer Jack - Drop Leg - A-Frame - 18" Lift - 3,500 lbs
- Shop: Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs - Qty 1
- Q&A: Recommended Flatbed Cargo Trailer Stabilizer Leg for Rear of Trailer
- Q&A: Is There A Shorter Stabilizer Jack Than The 11-1/2" TJ01RT-HD?
- Q&A: Replacement Drop Leg For Stabilizer Jack On 1994 Eagle Trailer
- Video: Stabilizer Jacks Review
- Search Results: electric jack
- Search Results: plug holder
- Video: Comprehensive Review: B and B Tow Plug and Safety Chain Holder
- Q&A: etrailer Swivel Jack e22ZV - What Is Retracted Height From Bottom Of The Bracket?
- Q&A: Can etrailer Swivel Jack be Install to Angle Iron on Homemade Trailer?
- Q&A: Handle Radius and Height Above Pipe Mount for etrailer Swivel Jack w/ Bolt-On Mounting Plate # e22ZV
- Q&A: Availability of Shorter Swivel Trailer Jack Sidewind with Wheel Caster
- Video: Review of etrailer Trailer Jack - Dual Swivel Jack Kit with Mounting Plates - e34RV
- Shop: Replacement Drop Leg with Foot for etrailer and Ram Square, Direct Weld Jacks - 7,000 lbs
- Shop: Replacement Footplate Keeper Pin for etrailer and Ram Square, Direct Weld Jacks - 7,000 lbs
- Shop: etrailer 2 Swivel Jacks w/ Bolt-On Mounting Plates - Sidewind - 15-1/2" Lift - 3,000 lbs
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Camper Jacks
Carlos G.
4/17/2024
Hi Kyle, Thanks for your reply. I was just about to order 2 sets of these stabilizing jacks, when another thought arose. It seems that the jacks are rated for 650 lbs. each when fully extended. My unit is 16 feet in length, with a total weight of about 4,500 lbs. Will these 4 corner jacks still be appropriate for our unit? To me it would seem not, because these jacks not rated like my current scissor jacks for my load. Thanks for taking the time to answer my questions and your great help.