Availability of Shorter Swivel Trailer Jack Sidewind with Wheel Caster
Updated 09/12/2025 | Published 05/28/2025
Question:
HI looking for a side wind weld on tongue jack wondering if there is something that is less than 24 in overall height that accepts a wheel?
asked by: Steve A
0
Expert Reply:
Hey Steve, is the height from the bottom of the mounting plate? If so, then I think the Fulton # FTJ120W0301 would work for what you are looking for as it has the shorter height below the mount and has a wheel caster.
expert reply by:
Jameson C
0
Fulton Swivel
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
etrailer Swivel Jack w/ Bolt-On Mounting Plate - Sidewind - 10" Lift - 3,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Sidewind Jack
- 2001 - 3000 lbs
- Manual Jack
- 10 Inch Lift
- Bolt-On
- With Rectangle Foot
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: jack wheel
- Shop: etrailer Swivel Jack w/ Bolt-On Mounting Plate - Sidewind - 10" Lift - 3,000 lbs
- Search Results: accessories and parts
- Search Results: door latch
- Search Results: trailer lights
- Search Results: viking
- Shop: etrailer Bolt-On Swivel Mounting Plate for 3,500-lb Trailer Jacks with a 5/8" Swivel Pin
- Video: LED Porch and Utility Light for RVs: The Breakdown
- Video: Review of etrailer Bolt on Swivel Jack Mounting Plate - e52JR
- Shop: etrailer Sidewind Trailer Jack - Swivel Bolt - 14" Lift - 2,000 lbs
- Q&A: Can etrailer Swivel Jack be Install to Angle Iron on Homemade Trailer?
- Shop: RV Exterior Lighting
- Search Results: stabilizer jacks
- Shop: etrailer 2 Swivel Jacks w/ Bolt-On Mounting Plates - Sidewind - 10" Lift - 3,000 lbs
- Q&A: etrailer Swivel Jack e22ZV - What Is Retracted Height From Bottom Of The Bracket?
- Shop: Round Pipe Mount Swivel Trailer Jack w/ Footplate - Topwind - 10-3/4" Lift - 2,000 lbs - Weld
- Shop: Round Snap Ring Swivel Trailer Jack w/ Footplate - Topwind - 10-1/2" Lift - 2,000 lbs - Bolt-On
- Q&A: Weld on Trailer Jack with Wheel That Swivels Up
- Q&A: what is the diameter of the Pin on the Etrailer Topwind Weld-On Swivel Jack
- Shop: etrailer Swivel Jack w/ Bolt-On Mounting Plate - Sidewind - 15-1/2" Lift - 3,000 lbs
- Q&A: Replacement Trailer Jack for Viking Legend Pop-Up Camper
- Search Results: plug holder
- Q&A: Handle Radius and Height Above Pipe Mount for etrailer Swivel Jack w/ Bolt-On Mounting Plate # e22ZV
- Q&A: Overall Height of etrailer Jack # e22ZV
- Video: Comprehensive Review: Stabilizer Jacks
- Video: Comprehensive Review: B and B Tow Plug and Safety Chain Holder
- Video: A Closer Look at the Stabilizer Jack
- Shop: Ladder Rack
- Shop: Tonneau Cover
- Video: Review of Yakima - Ladder Racks - Y01155
Jameson C.
9/12/2025
Hey Steve, did the Fulton jack with the wheel caster work out for your needs? I'm asking because your experience could guide others in choosing the right jack for their setup.