Solution for Bent Arm of Solera Awning

Question

Question:

lippert Part number 275055 shown on lippert drawing 644739 is bent. Gas strut 26” 124# is broken Do you have these parts?

asked by: Tim F

0

Expert Reply:

We've checked with Solera in the past about this same issue where the top arm of the awning support arm becomes bent and they have told us that individual part is not replaceable so you'd need to replace the entire assembly with the part # LC281154 that you referenced.

expert reply by: Jameson C

0

Answer 1

The fifth wheel or gooseneck towing capacity of a 2019 Ford F-350 Dually will range from 12,100 lbs to 34,000 lbs depending on options such as engine size, axle ratio, cab style etc. Therefore, you will need to verify your exact towing capacity and…

view full answer...

Answer 2

I recommend using the Optronics Flexible LED Light Strip - Weatherproof - White - 17' Long #UCL90CB, which is a weatherproof light that can be connected to an existing strip or wired directly to a 12v power source. These will be the perfect…

view full answer...

Answer 3

Let me start by stating the first step to finding the best option for your situation is to know your particular pin box style/number. The pin box number will be listed on a sticker on the pin box or stamped on the king pin. For example, if you have a…

view full answer...

Answer 4

We have replacement pitch arms for the Solera 69 inch awning setups like what you have with the part #LC375994 which would be all that you'd need.

view full answer...

Answer 5

No, Solera and Dometic awning components are not compatible with each other so the Replacement Support Arm Assembly for Solera Flat RV Awnings #LC281154 you referenced would not match up with the head of your Dometic awning. You would either have to…

view full answer...

Answer 6

There are a handful of reasons why the arm on your Lippert Solera awning might be bent; it could be a part (like the shock), sudden gusts of wind, too much weight from rain, or even something getting stuck in the track while you're retracting it.…

view full answer...

Answer 7

We do have both the parts you are looking for, the replacement head pin, as well as the end cap, and the end cap is available in both white and black so you can choose the correct color. What you need are the following: - Replacement Head Pin for…

view full answer...

Answer 8

To remove the old pin you'll need to remove the cover, remove the two retaining pins, and then slide the old pin out. To install the #LC93FR you'd just reverse the process.

view full answer...

Answer 9

Since you were looking at the Regal style idler head #LC672052 I'm assuming you need to replace the idler head pin on your Solera awning. You can remove the old pin and install #LC27WD for a replacement. If by key you mean a cotter pin, then yes…

view full answer...

Answer 10

We do have the exact bearings, races, and grease seal you need for your 4,400 lb Dexter axle, and while there isn't a single kit with the parts, you can get them all individually. What you will need are the following: Bearings #L68149 and…

view full answer...

Answer 11

The seal for your Dexter 4,400 lb axle is part #58846 which we also have in a pack of 2 listed as part #RG06-050 these have an inner diameter of 1.719" and an outer diameter of 2.565".

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Solution for Bent Arm of Solera Awning

Product Page this Question was Asked From

Continue Researching