What 7-Way Wiring Harness Is Compatible With My 2022 Hyundai Tucson

Question

Question:

I have a 2022 Hyundai Tucson with factory installed trailer hitch with flat four wiring. The owners manual says it an tow up to 3500 lbs but over 1500 it should be with trailer brakes. My trailers both weighing between 1500 and 2300 have electric brakes with 7 pin wiring. Is there a plug in adapter for my Tucson that will get me to 7 pin for the brakes that is easy. I currently use a Curt Bluetooth brake actuator. Thanks for the help

asked by: Wayne S

0

Expert Reply:

I did some research and I was unable to find a custom 7-way wiring harness for your 2022 Hyundai Tucson. You do have an option, but it will require some wiring splicing. The Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires, part # ETBC7, will fit your vehicle.

You will also need a brake controller. I like the Curt Echo Wireless Trailer Brake Controller - 1 to 2 Axles - Proportional, part # C51180, because it is wireless. You will not have to mess with any more of your wiring to get this installed properly. You will use a mobile app to monitor your trailer's braking. It is also a proportional brake controller. This means the same amount of force you apply to your brake controller will be applied to your trailer's brakes.

I have included product description link, a video installation link of this wiring kit on a 2020 Hyundai Palisade, and a video review link below. There should be some similarities between the installation of the Palisade and the Tucson.

expert reply by: Mark Smith

0

Answer 1

It looks like there currently are no custom fit wiring kits for your 2022 Hyundai Tucson Hybrid so I recommend using the following parts: - Curt Upgraded Circuit Protected Powered Tail Light Converter w Hardwire Kit and Tester #C59496 - Deka Heat…

view full answer...

Answer 2

Hey Martin, since your plan is to install a brake controller the 7-way kit you'd need on your 2022 Hyundai Tucson is the Tekonsha part #TK44ZR which comes with the needed brake controller wiring. The Curt does not have that so it wouldn't be…

view full answer...

Answer 3

Hey Danny, we can definitely help but we don't have just a kit for what you need. What you'd instead need is to run a 10 gauge wire like part #10-1-1 through a breaker like the part #9510 from the positive post of your battery to the 12 volt…

view full answer...

Answer 4

I am not sure what you mean by stabilizer bar but there are going to be three components required for you to tow your trailer if it does not have brakes or five components required if it does. I have listed these parts for you below. Without Brakes:…

view full answer...

Answer 5

The etrailer Trailer Hitch Receiver part #e38KR is a confirmed fit for a 2023 Hyundai Tucson Hybrid. In fact, the video I have attached for you below is on a Hybrid. This is an excellent trailer hitch option with bolt-on install, hidden design, and…

view full answer...

Answer 6

Yes, the Universal Wiring Kit #ETBC7 and the Tekonsha Prodigy P3 #90195 will also fit your 2011 Ford Escape. If you already have a 4-Way then you won't need anything else, however if you don't have a 4-Way then you will need part #118251 if…

view full answer...

Answer 7

Hello Roger; it will be possible to add a 7-way to your 2024 Hyundai Tucson. However, you will have to take a look at your vehicle to decide which one is right for you. If your current 4-way is plugged into the factory tow port behind the bumper and…

view full answer...

Answer 8

You basically already did verify that the center post of your 7-way is the 12 volt accessory circuit. Normally the center post is the reverse light circuit and the 12 volt pin is the 1:00 pin position. If your center pin is hot all the time then it…

view full answer...

Answer 9

I recommend tracing the wiring from the 4-pole connector back to see if it plugs into a connector or if it's hardwired to your tail lights before purchasing anything. The wire harness would get all the signals right at the tail lights if it was…

view full answer...

Answer 10

If you need a 4-way for your 2024 Hyundai Tucson you would want the part #CU94FR or for a 7-way you would want the part #C68JR. These are both custom fit kits that install easily without requiring any hardwiring or splicing.

view full answer...

Answer 11

Hey Wes! You can order replacement hardware for your Curt Hitch using the Replacement Hardware Kit for Trailer Hitches #RHK. However, you will have to identify which hitch you have to get the right hardware. If it looks like the #C13900 then enter…

view full answer...

Answer 12

We have a pretty simple kit designed specifically for use with the Curt Echo #C51180 to convert a 4-way to a 7-way and have all of the needed circuits active for the Echo to function with the #ETBC7L which is a simple 4-way to 7-way adapter that also…

view full answer...

What 7-Way Wiring Harness Is Compatible With My 2022 Hyundai Tucson

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching