How To Install The Curt Auxiliary LED Indicator Lights C53201 With Load Resistors DI34ZR
Updated 04/05/2024 | Published 12/10/2021
Products Featured in This Question
Question:
Hello. I have a 4-bike, hitch-mounted Kuat bike rack. I have been pulled over twice now for the rack not having lights and the mounted bikes obstructing my vehicles taillights. I want to mount some lights and the subject Curt lights seem like the best alternative. However, I already know load resistors will be required for my vehicle. Your QandA section recommends DI34ZR for use with the Curt lights. However, I cant find any installation instructions. I like the Kurt lights because they use simple connectors. However, it appears the resistors would have to be spliced in somewhere. Before I purchase, do you have instructions or a diagram of how these resistors are installed with the Kurt lights? Thanks.
asked by: Theodore E
Expert Reply:
To wire the Load Resistor Kit for LED Turn Signals # DI34ZR into your vehicles turn signals you will need to find your turn signal wire for your vehicle. Once that wire is identified, take the one end of the wire and the turn signal wire and connect to the quick splice connector. Make this connection by crimping the wires together with a crimping tool like # PTW30764. From here you'll connect the other white wire and ground this wire to a good ground source.
The Curt Auxiliary LED Indicator Light # C53201 is even easier to install, simply plug the 4 way flat connector into your existing 4 way connector, and color match the plugs to the receptacles.
Product Page this Question was Asked From
Curt Auxiliary LED Indicator Lights
- Accessories and Parts
- Hitch Bike Rack
- Hitch Cargo Carrier
- Lights
- CURT
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Curt Auxiliary LED Indicator Lights
- Video: Curt Auxiliary LED Indicator Lights Review
- Video: Curt Auxiliary LED Indicator Lights Review
- Shop: Vehicle Tow Bar Wiring
- Shop: Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Video: The Low-Down on the Curt Auxiliary LED Indicator Lights
- Search Results: curt lights
- Search Results: dielectric grease
- Search Results: tie down straps
- Shop: Hollywood Racks Safety LED Light Bar for Bike Racks
- Q&A: Tail Light Kit For Kuat NV Base Bike Rack
- Video: Detailed Breakdown of the Magnetic Tow Lights
- Shop: Universal Magnetic Tow Lights - Red LEDs - 20' Wiring Harness with 4-Way Flat Trailer Connector
- Video: A Closer Look at the LED Tail Lights for Saris MHS System
- Video: Comprehensive Review: LED Tail Lights for Saris MHS System
- Shop: LED Tail Lights for Saris MHS System
- Shop: Dielectric Grease for Electrical Connectors, 2 oz.
- Q&A: Recommended Auxiliary Light Kit For a Kuat Bike Rack
- Search Results: curt 53201
- Search Results: bike rack lights
- Search Results: lights for bike rack
- Search Results: di34zr
- Shop: Tail Light Kit and License Plate Holder for Thule Epos Bike Racks
- Q&A: How to Add Lights to the Yakima HoldUp Bike Rack
- Q&A: Solution for Lights on Yakima OnRamp LX
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Accessories and Parts
Walt
3/16/2024
53201. No indication which is left or right. Just Y and B. Running through tubes so has to be correct first time. Car not wired yet so no test possable