Bearing Kit for Dexter 3,500 lb Trailer Axle

Question

Question:

I have a single axle utility trailer I want to replace bearings on. The sticker on the axle says its a Dexter 5705005 3500 lb axle. serial # 212290675 Which bearing set do I need for this? Thanks

asked by: Andy

0

Expert Reply:

The correct bearing kit for a Dexter 3,500 trailer axle is the part # BK2-100.

expert reply by: Jameson C

0

Answer 1

I do have an option for you but you likely have an L68149 inner bearing an L44649 outer bearing which is commonly found on 3,500 lb axles and is the most common axle capacity. I am not aware of any trailer or hub that uses two L68149 bearings but you…

view full answer...

Answer 2

The Dexter D35 axle is a 3,500 lb trailer axle so for a bearing kit you would want the part #BK2-100 that you referenced.

view full answer...

Answer 3

Hi John, I reached out to Dexter to confirm what bearings and seals match the tag number from your axle. The bearings and seal that work fit your Dexter 7K axle with #152785392 are: -Inner Bearing: etrailer replacement trailer hub bearing part #25580…

view full answer...

Answer 4

On Dexter axles manufactured after April 2001 you will be able to find the serial number stamped on the rear portion of the axle tube approximately 18" from the passenger side hub. Depending on the condition of the axle you may need some chalk…

view full answer...

Answer 5

With a 3,500 pound Dexter axle your bearings are #L44649 for the outer and #L68149 for the inner. So you were looking at the correct bearing kit with part #BK2-100.

view full answer...

Answer 6

Hello Phillip, thanks for reaching out, and for the picture. Your Dexter axle uses the standard bearing sizing for a 3,500 lb axle. It uses the #L68149 inner bearing and #L44649 outer bearing. The seal is a 1.719" ID and 2.565" OD. We offer…

view full answer...

Answer 7

The axle tag on your 3,500 lb Dexter EZ-Lube axle will have the serial number that would allow Dexter to identify the axle. You could also look at the bearings for part numbers or measure the spindle to find the inner diameter of the bearings and…

view full answer...

Answer 8

The correct replacement bearing and seal kit for your 3,500 lb Dexter Axle is the Hub Bearing Kit #BK2-100 for the #84 spindle. This kit comes with inner bearing #L68149, outer bearing #L44649, and a grease seal with a 1.719" ID and 2.565"…

view full answer...

Answer 9

Yes, Dexter 3,500 lbs Axles use the same Inner Bearing item #L68149 and Outer Bearing item #L44649 no matter what size lug pattern you are using be it 6 or 5. For a complete replacement kit you will want the Hub Bearing Kit for Lippert, Dexter, and…

view full answer...

Answer 10

Sounds like you are looking for a bearing kit for a hub on your 3,500 lb Dexter axle. Dexter 3,500 lb axles are very common. They might be the most common axle found on trailers actually. Because of that we know that they bearing kit you need is the…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Bearing Kit for Dexter 3,500 lb Trailer Axle

Product Page this Question was Asked From

Continue Researching