Bearing Kit for Dexter D35 Trailer Axle

Question

Question:

Hi I need to replace the bearings on a dexter d35 axel for a travel trailer not sure of the part number I uploaded some info for the axel thanks alot.

asked by: Feuaz K

0

Expert Reply:

The Dexter D35 axle is a 3,500 lb trailer axle so for a bearing kit you would want the part # BK2-100 that you referenced.

expert reply by: Jameson C

0

Dexter D35 Trailer Axle
(click to enlarge)

Answer 1

Hey Mark, thanks for reaching out! I see you purchased the Dexstar Steel Spoke Trailer Wheel #AM20353. Were you wanting to get a 205/75R14 tire as well? I wasn't able to find anything online referring to the part number you mentioned, but I'd…

view full answer...

Answer 2

A replacement tang-style spindle washer like part #5-101 is intended to be installed behind the castle nut and have its prongs bent down so that they prevent the castle nut from rotating on an E-Z Lube type spindle. The castle nut holds the washer in…

view full answer...

Answer 3

Hey Thomas, The pin you're referring to is a cotter pin #165649 that will slip through the a hole in the spindle and then is usually split and bent around the castle nut to prevent the pin from falling out and the castle nut from backing off. I…

view full answer...

Answer 4

The old Reese V-5 weight distribution system is not rated by the vehicle. It will be compatible with vehicles and trailers determined by the loaded tongue weight of the trailer along with any any cargo behind the rear axle of the towing vehicle.…

view full answer...

Answer 5

It sounds like you're asking about the torque spec for the castle nut on your 3,500 lb axle. There is no specific torque rating when installing the castle nut on any axle. You want to run the nut down until there is no side to side play in the…

view full answer...

Answer 6

Basically you'll run a feed line of 10 gauge wire like the part #10-1-1 (sold by the foot) back to the axles and from there you'll run power to each axle. I attached a diagram that shows how this is done on a tandem axle trailer. For a triple…

view full answer...

Answer 7

It sounds like you want a diagram of the wiring for your trailer and breakaway system. I am attaching an article with pictures about wiring trailers. I am also attaching an article with pictures on wiring a breakaway kit. I also recommend making the…

view full answer...

Answer 8

Hey Ed! The Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles #84546UC3-EZ will work as a spare for your D35 axle. This is pre-greased which is exactly what you want for a spare. What kind of trailer do you have?

view full answer...

Answer 9

The bolts that come with the #BRKH10AS are grade 5 bolts. The bolts and nuts are a zinc plated steel and not stainless steel.

view full answer...

Answer 10

It most likely would be wide enough. A 205/75-14 tire can fit on a 5, 5-1/2, 6 or a 6-1/2 inch wide rim. A 215/75-14 tire fits on a 5-1/2, 6, 6-1/2 or a 7 inch rim. It's nearly impossible to determine the correct width of a given rim unless the…

view full answer...

Answer 11

The tire size of 215/75R14 fits rim widths that are from 5 inches to 7 inches. To see all of the 14 inch wheels we offer check out the link I attached. You will need to know what bolt pattern you would need to fit your trailer as well. I attached a…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Bearing Kit for Dexter D35 Trailer Axle

Product Page this Question was Asked From

Continue Researching