Bearing Kit Recommendation for Dexter 3,500 lb Axle

Question

Question:

Do you sell rebuild kits for Dexter 3500 lb axles? From inner seal out to dustdust cap?

asked by: Chris

0

Expert Reply:

Sounds like you are looking for a bearing kit for a hub on your 3,500 lb Dexter axle.

Dexter 3,500 lb axles are very common. They might be the most common axle found on trailers actually. Because of that we know that they bearing kit you need is the # BK2-100 which includes the correct bearings and seal.

expert reply by: Jameson C

0

Answer 1

Hi John, I reached out to Dexter to confirm what bearings and seals match the tag number from your axle. The bearings and seal that work fit your Dexter 7K axle with #152785392 are: -Inner Bearing: etrailer replacement trailer hub bearing part #25580…

view full answer...

Answer 2

Hello Phillip, thanks for reaching out, and for the picture. Your Dexter axle uses the standard bearing sizing for a 3,500 lb axle. It uses the #L68149 inner bearing and #L44649 outer bearing. The seal is a 1.719" ID and 2.565" OD. We offer…

view full answer...

Answer 3

The correct replacement bearing and seal kit for your 3,500 lb Dexter Axle is the Hub Bearing Kit #BK2-100 for the #84 spindle. This kit comes with inner bearing #L68149, outer bearing #L44649, and a grease seal with a 1.719" ID and 2.565"…

view full answer...

Answer 4

The axle tag on your 3,500 lb Dexter EZ-Lube axle will have the serial number that would allow Dexter to identify the axle. You could also look at the bearings for part numbers or measure the spindle to find the inner diameter of the bearings and…

view full answer...

Answer 5

Yes, Dexter 3,500 lbs Axles use the same Inner Bearing item #L68149 and Outer Bearing item #L44649 no matter what size lug pattern you are using be it 6 or 5. For a complete replacement kit you will want the Hub Bearing Kit for Lippert, Dexter, and…

view full answer...

Answer 6

With a 3,500 pound Dexter axle your bearings are #L44649 for the outer and #L68149 for the inner. So you were looking at the correct bearing kit with part #BK2-100.

view full answer...

Answer 7

The correct bearing kit for a Dexter 3,500 trailer axle is the part #BK2-100.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Bearing Kit Recommendation for Dexter 3,500 lb Axle

Product Page this Question was Asked From

Continue Researching