Do You Carry A Lighted License Plate Bracket For a Motorcycle License Plate On a Enclosed Trailer?

Question

Question:

I need to get a lighted license plate bracket for the rear ramp door of my enclosed cargo trailer. The license plate size is smaller than standard license plates. I think it’s motorcycle sized. Optimally, I’d like a bracket that allows me to secure all four corners of the plate. Do you have a lighted bracket that would fit my needs?

asked by: Mark S

0

Expert Reply:

While we do not have an exact part we do have all the parts that will allow you to mount your smaller license plate to your enclosed cargo trailer.

First the Trailer License Plate Mount Bracket # LP10SB will give you an attachment point for the license plate and light. This is made of a rustproof black polymer that will last.

A Peterson Great White LED Trailer License Plate Light # M290C-BT2 will attach to the top of the bracket to light up the license plate. You will need to provide the mounting hardware for this light.

Finally you can use a Neo Motorcycle License Plate Frame # CR77050 to secure all 4 corners or the license plate for additional support and rigidity.

expert reply by: Bud M

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

I do have an option for you but the Draw-Tite Trailer Hitch Receiver part #37130 will not work for you. The factory towable bumper has different brackets than the non-towable bumper which interferes with the installation of this hitch. Instead, I…

view full answer...

Answer 3

Hey Tad! We aren't able to guarantee a specific DOT date code before an order ships, since tire inventory can vary as shipments come in. That said, the tires are stored properly away from UV exposure and other conditions that can prematurely age…

view full answer...

Answer 4

Hello Shawn, The 24x60 etrailer Enclosed Cargo Carrier for 2" Hitches - Steel - 440 lbs #e54VV is a great option for hauling your gear while keeping it protected. We do have a cover available for it as well! You will want the Cargo Cover for…

view full answer...

Answer 5

Hi Bob, The hubs part #AKIHUB-545-2-G-EZ-2K come pre-greased with a lithium based grease, so when it's time to add or replace grease, I'd stick with another lithium based high temperature #2 wheel bearing grease like the Dexter High…

view full answer...

Answer 6

The inner diameter of the #Foot Pad #2500-25 is approximately 1-11/16 inches.

view full answer...

Answer 7

Hi Larry; something like the Optronics LED Trailer License Plate Light #LPL56CB would be the best option for the License Plate Holder for Kuat Piston Pro X #KU49RR. You can place this between your license plate and the holder. The #328-003-71BE would…

view full answer...

Answer 8

Hey Randy, good question. Yes, the TowSmart #TS85SR is 100% copper wire, not copper-clad aluminum. That’s a big deal for trailer wiring because copper carries current better, holds up to vibration, and resists corrosion a lot better over time. You’ll…

view full answer...

Answer 9

No long-term contract, Natalie - but a service plan is required to use the trackers. When you buy the 3000 with wifi assist #PM84FR, 5000 #PM64FR, or 5000 with wifi assist #PM74FR from etrailer, you’re purchasing the hardware/device only. To activate…

view full answer...

Do You Carry A Lighted License Plate Bracket For a Motorcycle License Plate On a Enclosed Trailer?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching