License Plate Light for License Plate Holder for Kuat Piston Pro X

Question

Question:

Hi! Which license plate lights would work best with the Kuat License Plate Mount on the link below? License Plate Holder for Kuat Piston Pro X KU49RR Thank you for you time and assistance. Best regards, Larry

asked by: Larry M

0

Expert Reply:

Hi Larry; something like the Optronics LED Trailer License Plate Light # LPL56CB would be the best option for the License Plate Holder for Kuat Piston Pro X # KU49RR. You can place this between your license plate and the holder. The # 328-003-71BE would also work since it is a full frame that fits around your license plate.

You can connect the wires on the light to the Hopkins Endurance Easy-Pull Harness # HM38134 so you can plug it into the 4-way on your vehicle for power.

Any big trips coming up with your bikes and Piston Pro X?

expert reply by: Robin H

0

License Plate Holder for Kuat Piston Pro X
(click to enlarge)

Robin H.

3/4/2026

Hey Larry, how did the Optronics LED light work out with your Kuat License Plate Mount? Your feedback could really help others looking to light up their plates the same way. Did the wiring with the Hopkins harness go smoothly?

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

License Plate Light for License Plate Holder for Kuat Piston Pro X

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching