Trailer Hitch, Wiring & Brake Controller For 2021 Ram ProMaster 3500

Question

Question:

Hello there. I have a 2021 Ram ProMaster 3500. I'm looking for a trailer hitch, hitch wiring and brake controller, can you recommend the right parts for me please?

asked by: Devin E

0

Expert Reply:

We can absolutely get you the right parts to add a trailer hitch receiver, wiring, and brake controller to your 2021 Ram ProMaster 3500 without the factory tow package. Here are the exact parts you'll need in order to do that:

- Curt Trailer Hitch Receiver # C13295

- Tekonsha OEM Replacement Vehicle Wiring Harness with Brake Controller Adapter - 7 Way Trailer Connector # 22112

- Tekonsha Prodigy P3 Trailer Brake Controller # 90195

The Tekonsha wiring harness, although its title says "Replacement" is not actually a replacement despite the title. It includes everything needed, including the wiring harness that will plug into a Tekonsha brake controller, so it's both the easiest and most cost-effective wiring harness. To mount the 7-way you will also need the Mounting Bracket for 7-Way # 18138.

Finally, the P3 brake controller can be plugged right in, will give you the most consistently smooth braking, and is easy to use due to its bright LCD screen and continual diagnostic checks with safeguards to prevent shorts.

expert reply by: Kyle S

0

Answer 1

Hello James, I am at a loss why Draw-Tite #75882 classified theirs as a class 4, it can handle the same weight as the Curt #C13207. The most concealed hitch would be the Curt #C13295, but it has the lowest towing weight so I am crossing that one off…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Hey George, for your 2026 Toyota RAV4 Hybrid we have the Curt hitch part #C34FR62ZY as a confirmed fit but it's on a little bit of a backorder at the moment which is why you don't see any hitch options in our fitguide. The hitches from…

view full answer...

Answer 12

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Trailer Hitch, Wiring & Brake Controller For 2021 Ram ProMaster 3500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching