Bolt Size & Thread Tap For C11265 & C13140 Trailer Hitches

Question

Question:

Hi , Are the bolts for the c13149,2007 corolla, the same for c11265 2018 rav4? I had to tap the c11265 with a-12mm-1.25 27/64. now i have to tap the c13149!Are the bolts the same? Will this tap 12mm-1.25 27/64 work? Thank you

asked by: Paul G

0

Expert Reply:

Yes, the bolts are indeed both M12 x 1.25 bolts for both the hitches you mentioned, the Curt Trailer Hitch Receiver # C11265 and # C13149.

So you can use a thread tap for those M12 x 1.25 bolts and you'd be set.

expert reply by: Kyle S

0

Answer 1

The six hex bolts that come with the etrailer Trailer Hitch Receiver #E98869 for attaching to your 2019 Nissan Frontier are M12-1.25 x 35mm. The washers are 7/16" conical tooth washers. If you are in need of replacements we have the Replacement…

view full answer...

Answer 2

Hey Chris, the Curt hitch part #C14081 that fits your 1998 Chevy K2500 uses the bolt size 1/2-13 UNC,2,GRD8.

view full answer...

Answer 3

The Curt Hitch part #C13149 is a confirmed fit for your 2016 Toyota RAV4. You can't reuse the install hardware since the bolts are considered one-time-use. You would need the part #RHK to get new hardware. On the product page you would just need…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hey Kelly! The Curt 13146 fits 2016 - 2022 Honda Pilot. What you need for your 2026 Honda Pilot is the Curt #C22HR. This has a bolt-on installation and does not require any cutting or trimming of the bumper so you won't be modifying the vehicle.…

view full answer...