Electric Jack Wont Clear Tailgate on Truck.
Updated 04/05/2021 | Published 04/01/2021 >
Products Featured in This Question
Question:
Hi There, This jack works great, however, I cannot open my trucks tail gate, and I have seen rotate them 90 degrees, and they work fine, but I have not been able to figure out, how to rotate this one. Is this possible? If so, coul you please send me some instructions? Thank you in advance
asked by: Paul Q
Expert Reply:
Your Electric Jack # EJ-3520-BBX would be difficult to turn the 90 degrees that you are looking for. The mounting flange only has the 3 outward tabs which means you would have to either turn the jack 120 degrees or drill new holes into your mounting flange on your trailer.
The Bulldog Powered Drive Trailer Jack # BD500187 comes with a round mounting plate that has provisions for multiple mounting patterns such as the 90 degrees that you are looking for. This would be the easiest way to get to the 90 degrees turn and explains why you sometimes see jacks like that.
Another option to consider is a longer Ball Mount # BM20 or Weight Distribution Shank # EQ90-02-4500. This would move your ball farther from your truck and give you the clearance for your tailgate. I recommend measuring the length of your current shank vs what you need to allow clearance for your tailgate. This may prove to be the better option for you as you will gain space and not lose your work light the jack provides.
Product Page this Question was Asked From
Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- A-Frame Jacks
- Steel
- 3001 - 4000 lbs
- Electric Jack
- 18 Inch Lift
- Bolt-On
- 1 Jack
- RAM
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: DIY Install Curt T-Connector 4-Pole Wiring Harness - 2022 Toyota Highlander
- Shop: Trailer Wiring
- Q&A: How Can I Determine If My 2023 Toyota Highlander LE Has The Factory Tow Package Or Not?
- Shop: Stromberg Carlson Electric A-Frame Tongue Jack - 18" Lift - 2,500 lbs
- Video: The Low-Down on the Stromberg Carlson Electric A-Frame Tongue Jack
- Q&A: Shortest Profile Electric Tongue Jack Available For Hatchback Door Clearance
- Search Results: receiver extender
- Shop: Curt Mounting Bracket for 4-Pole Flat Trailer Connector
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Shop: Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black
- Shop: Curt MV Weight Distribution System - Round Bar - 6,000 lbs GTW, 600 lbs TW
- Q&A: Can I Turn The Trailer A-Frame Jack To Achieve Clearance For My Lift Gate/Tailgate?
- Shop: etrailer Electric Trailer Jack - Drop Leg - A-Frame - 18" Lift - 3,500 lbs
- Q&A: Replacement Electric Tongue Jack that Will Allow Full Opening of Tailgate on Tow Vehicle
- Video: Feature Breakdown: Flexco Manual Pull-Out Step for RVs
- Q&A: Troubleshooting Malfunctioning Bulldog Power Jack # BD500199
- Q&A: Does etrailer 5K Electric A-Frame Jack Need an In-Line Fuse?
- Q&A: What Is The Difference Between The Electric Trailer Jack e23ZV And e55ZV?
- Search Results: 10k equalizer
- Search Results: e2 trunnion fastway
- Search Results: weight distribution hitch
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement




