Can the Erickson Big Bed Load Extender Be Used As a Roof Extender

Question

Question:

can the erickson big bed load extender be converted to a single bar roof rack like the darby extend a truck? Thanks.

asked by: Doug H

0

Expert Reply:

The Erickson Big Bed Load Extender part # EM07600 is a bed extender only. That said, we have plenty of options which are both a bed extender and roof extender like the Erickson Big Bed Junior part # EM07605 or the Malone Axis Truck Bed and Roof Load Extender part # MPG907.

expert reply by: Conner L

0

Answer 1

Hello Jim, Great question, I went to Malone's site and and I do not see that they make one with a 48" roller. The great thing about the Malone Axis Truck Bed and Roof Load Extender with Load Roller #MAL32VR is that it is adjustable, the…

view full answer...

Answer 2

Hello Russ. As far as the Malone Axis Truck Bed and Roof Load Extender with Load Roller #MAL32VR, the roller itself is 42" wide. The roller can extend 53", and this is measured from the center of the roller to the center of the hitch pin…

view full answer...

Answer 3

The only hitch mounted option wouldn't be an actual carrier, but a support like the Malone Axis #MAL32VR. This would require the installation of a trailer hitch like the #76138 you looked at. More than likely you won't need this to mount your…

view full answer...

Answer 4

The roller part #MAL52VR is 2 inch in diameter and has a 375 lb capacity when used in the upright carrier part #MAL32VR.

view full answer...

Answer 5

The Malone Axis Load Roller for Malone Truck Bed and Roof Load Extender - 42" Long, part #MAL52VR, that comes with the Malone Axis Truck Bed and Roof Load Extender with Load Roller, part #MAL32VR, is fixed in length. It does not extend in and…

view full answer...

Answer 6

Hey Paul, The Flint Hill Goods Truck Bed Extender #FHG89ZR gives a 3 inch extension when in the vertical position, so it may clear the spare tire, depending on where the receiver is on your Jeep. A hitch extender should not be used as that would…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Can the Erickson Big Bed Load Extender Be Used As a Roof Extender

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching