Does The Axis Load Roller Extend In And Out On The Malone Truck Bed And Roof Load Extender

Question

Question:

Does the roller extend in and out

asked by: Mike

0

Expert Reply:

The Malone Axis Load Roller for Malone Truck Bed and Roof Load Extender - 42" Long, part # MAL52VR, that comes with the Malone Axis Truck Bed and Roof Load Extender with Load Roller, part # MAL32VR, is fixed in length. It does not extend in and out. You will have to remove this when the extender is at a length less than 42".

I have included a product description link and a video review link below.

expert reply by: Mark Smith

0

Answer 1

Hello Jim, Great question, I went to Malone's site and and I do not see that they make one with a 48" roller. The great thing about the Malone Axis Truck Bed and Roof Load Extender with Load Roller #MAL32VR is that it is adjustable, the…

view full answer...

Answer 2

The roller part #MAL52VR is 2 inch in diameter and has a 375 lb capacity when used in the upright carrier part #MAL32VR.

view full answer...

Answer 3

The Erickson Big Bed Load Extender part #EM07600 is a bed extender only. That said, we have plenty of options which are both a bed extender and roof extender like the Erickson Big Bed Junior part #EM07605 or the Malone Axis Truck Bed and Roof Load…

view full answer...

Answer 4

The only hitch mounted option wouldn't be an actual carrier, but a support like the Malone Axis #MAL32VR. This would require the installation of a trailer hitch like the #76138 you looked at. More than likely you won't need this to mount your…

view full answer...

Answer 5

Hello Russ. As far as the Malone Axis Truck Bed and Roof Load Extender with Load Roller #MAL32VR, the roller itself is 42" wide. The roller can extend 53", and this is measured from the center of the roller to the center of the hitch pin…

view full answer...

Answer 6

Hey Paul, The Flint Hill Goods Truck Bed Extender #FHG89ZR gives a 3 inch extension when in the vertical position, so it may clear the spare tire, depending on where the receiver is on your Jeep. A hitch extender should not be used as that would…

view full answer...

Answer 7

In this case I would go with the low side. Odds are you wont' be completely maxed out and sitting at 830 lbs. As soon as some of that water is gone you will also be under the 800 lb mark. The #17302 may give you a rough and rigid ride since fully…

view full answer...

Answer 8

Hello Alan, Great question! The specifications of the Lock Pins that come with the #MAL32VR are 3/8" diameter, and 3" long. We do not have anything that is going to be a good fit, I did reach out to the tech at Malone to see if a 1/4"…

view full answer...

Answer 9

No, there is no drilling required to install any component of the Malone Axis Truck Bed and Roof Load Extender with Load Roller - 2" Hitches #MAL32VR or just the Malone Axis Load Roller for Malone Truck Bed and Roof Load Extender - 42" Long…

view full answer...

Answer 10

It's probably not the best way to transport a kayak on a 2015 Honda CR-V but it's also not the worst. The Malone Axis Truck Bed and Roof Load Extender with Load Roller part #MAL32VR should work fine for what you're wanting although…

view full answer...

Answer 11

The Malone Axis Truck Bed and Roof Load Extender with Load Roller #MAL32VR will allow you to more easily load your canoe on the Malone TradeSport Truck Bed Ladder Rack #MAL55VR. This roller also acts as an extension to provide a more stable platform…

view full answer...

Answer 12

The Malone Load Extender part #MAL32VR that you referenced does not have ability to angle back like the Rhino Rack T-Load part #RTL002 has so your best option would be to go with the Rhino Rack.

view full answer...

Does The Axis Load Roller Extend In And Out On The Malone Truck Bed And Roof Load Extender

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching