Diameter and Weight Capacity of Malone Truck Bed Extender Roller # MAL52VR

Question

Question:

I want to use this roller to load a drift boat onto a trailer. it would be mounted on the back end of the trailer. what is the diameter of the roller and how much weight would the roller handle. the boat weights approx 350 LBS. Thanks

asked by: Kevin C

0

Expert Reply:

The roller part # MAL52VR is 2 inch in diameter and has a 375 lb capacity when used in the upright carrier part # MAL32VR.

expert reply by: Jameson C

0

Answer 1

The way the Ladder Roller for Rhino-Rack Heavy-Duty Crossbars #RR1500 works is that the top bracket mounts into the t-tracks of your bars and roller is on the side. That means they can't be flipped upwards since there are no t-tracks on the side…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

I contacted our representative at Hidden Hitch about the Draw-Tite Trailer Hitch, part #24677. The representative at Draw-Tite informed me that the thickness of the tubing for part #24677 is 3/16 inches. The arms of the hitch that connect to the…

view full answer...

Answer 4

Hey Damon! Rhino Rack just has the 75-degree angled brackets that come in the Rhino-Rack Ski and Fishing Rod Carrier Kit #RR572-43159, and they don't have one with a 90-degree bracket. Are you just trying to give yourself as much space on your…

view full answer...

Answer 5

Just a single difference exists between the Curt and etrailer trailer hitches for your 2024 Mercedes Sprinter 2500 with a factory step bumper, which is the finish. The etrailer hitch has a matte black finish, while the Curt hitch has a glossy black…

view full answer...

Answer 6

You could use the Master Lock lock set part #2848DAT which comes with a trigger latch lock for the coupler of your Ranger boat trailer and a hitch lock that fits a 2 inch hitch and a 1-1/4 inch hitch. These all use the same key as well.

view full answer...

Answer 7

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 8

I spoke to my contact at Rhino Rack and he informed me that the length of the roller on the Rhino Rack Ladder Roller #RR1500 that you referenced is 56-1/4 inches. Check out the picture I attached to see this measurement.

view full answer...

Answer 9

Measuring to pick out the correct slide topper for an RV like your 2018 Forest River Rockwood is pretty easy. You have to measure the box width including the flange on it and you'll be set. So the Solera part #LCV000163288 that you referenced is…

view full answer...

Answer 10

We do offer slide topper awnings that are larger than the Solera 13' Slider #LCV000165061 that you referenced. In a 16-foot we offer part #LCV000194925 in black and part #LCV000163307 in white. We also offer 15-, 14- and 14-1/2-foot versions. You…

view full answer...

Answer 11

In this case I would go with the low side. Odds are you wont' be completely maxed out and sitting at 830 lbs. As soon as some of that water is gone you will also be under the 800 lb mark. The #17302 may give you a rough and rigid ride since fully…

view full answer...

Diameter and Weight Capacity of Malone Truck Bed Extender Roller # MAL52VR

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching