Replacement Hitch Pin for Yakima BackRoad 4-Bike Rack

Question

Question:

what is the size of the hitchbolt for yakima backroad 4?

asked by: Donnie

0

Expert Reply:

I checked with Yakima and the correct replacement hitch pin you need for your BackRoad is the part # Y8890176.

expert reply by: Jameson C

0

Answer 1

I reached out to my contact at Yakima and their bike racks use either #Y8890176 for racks that fit a 1-1/4 inch receiver and #Y8890200 if the rack fits a 2 inch. To lock either pin use #Y07235 which attaches over the hitch pin and uses an included…

view full answer...

Answer 2

Yakima has a few different anti-rattle threaded hitch bolt designs and the one you want for your Yakima EXO SwingBase Swing Away Hitch Extender #Y34VR is part #Y52FR on our site. This is the same as the 8880953 you mentioned, it just has our part…

view full answer...

Answer 3

Yes, the Holdup for 1-1/4 inch hitches requires a different, smaller hitch pin. For that you'd need the part #Y90195 which comes with the new wrench you'd need and the smaller hitch pin for use with the #8880580.

view full answer...

Answer 4

To convert your Yakima HoldUp 2 Bike Rack for 2" Hitches #Y02443 so that it will fit a 1-1/4" hitch receiver you need the Replacement Tongue #8880581 along with the Hardware Kit #Y90195. Please note that when using this smaller tongue you…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Replacement Hitch Pin for Yakima BackRoad 4-Bike Rack

Product Page this Question was Asked From

Continue Researching