Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replaces your power landing gear follow leg and snap pin. Enjoy the power setup while you are out camping and know that your RV or fifth-wheel will be steady and secure.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today I'm going to take a look at the replacement fifth-wheel RV landing gear follow leg with the snap pin for Lippert Components RVs. This will replace your follow leg and snap pin on the Lippert Components power landing gear. It's designed to fit the standard power landing gear, supports your fifth-wheel to prevent unwanted movement. It's designed to connect right here to the lead jack and the landing gear set, with a connecting rod or a cross shaft, which we do sell separately. It does include the two zerk grease fittings, one right here, one right here for lubrication of the jack. This is constructed of a heavy-duty steel, has a nice black powder coat finish to it.
Part is made in the U.S.A.A few specs on this, the weight capacity. If it's a manual crank is going to be 4,000 pounds per leg. If it's a dual motor, it will be 4,000 pounds per leg. And if it's a single motor it'd be 2,500 pounds per leg. Overall height, which will be measured from the top to the very bottom of the inner tube right there, if we put a tape measure on that right here ...
Very top here you're going to see is right at 32 inches overall height. Total width on this going to be right at 2 1/2 inches wide. Now the outer tube, which is the black portion from here to the very bottom on the black tube, that's going to be right at 29 1/2 inches tall.And then the bracket stops or the weld stops right here on each side. This is where your jack will attach to the mounting brackets on your trailer. Outside the outside, which will be from here to down here.
You're going to be looking right at 17 1/2 inches, and inside the inside, 15 1/2 inches. So, each weld stop is about an inch wide. But that should do it for the review on the replaces fifth-wheel wheel RV landing gear follow Leg with the snap pin for the Lippert Components RVs.
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
Ratings & Reviews
Anthony R.
9/9/2017
Great, very happy with product
Guyn
1/24/2018
no problems after a year, working fine.
Larry S.
9/18/2019
product works great and has solved the problems i had. I have been telling everyone i know that if you need parts for your RV you must call Etrailer first you wont be sorry.
Stanley
9/14/2019
Flawless....
Lc179014
9/13/2019
The leg is working great, knowledge staff, great products and fast shipping.
Mike
11/18/2018
Great no problems
Ron J.
9/11/2016
very good, makes me a happy camper
Ron H.
5/5/2018
The 5th wheel landing gears are doing great!
Levi
6/24/2021
After 1 year, it is holding strong!
John S.
9/13/2017
Working great no problems
William
8/23/2024
Works great easy to install
Frank M.
1/15/2019
Great
Frank M.
1/15/2019
All is good. Thanks for your help. We still have the 5th wheel, and all seems to be working fine. Fifth wheel put away for the winter, excited to continue our journeys.
Steve M.
3/8/2018
Excellent
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Richard
3/15/2019
Still working properly, I’ve had no issues with it...