Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replaces the landing gear lead leg assembly for your Lippert Components Venture 5th Wheel RV landing gear. Mounts to the inside of the frame rail.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey everyone. I'm Ellen here at etrailer.com. Today, we're taking a look at the replacement lead leg. This is going to be for our venture fifth wheel RV landing gear, and this is going to be a direct replacement for that. So it'll be our lead leg that has the gearbox, the motor mounted on it, and then kind of gives the direction for our follow leg for that landing gear to help get everything stabilized and leveled out. Now, the main thing that I'm going to go over with you guys today are all the measurements for this.
It is going to be a standard size. So our outer tube has a length of 29 and a half inches going from the top to the bottom of this black outer tube. The width is two and a half inches, again, for that outer tube. The inner tube is two and a quarter.And then our drop leg, which is the innermost tube is two inches. As far as the heights and everything, we'll go over that in just a second.
We've also got two weld steps here, which are going to be a pretty standard size, and these are going to be on the outside of the landing gear. So this is going to be mounted in between your frame. So each of those weld stops will be our attachment point there, the outermost of the outside measurement, it's going to be 17 and a half inches. So from the very top of the top weld stops, the very bottom of the bottom weld stop is at 17 and a half inches. And then our inside measurement is going to be 15 and a half.
So from the bottom of the top to the top of the bottom.Now whenever this is fully extended, if we have the jack run all the way out to the end of that screw and then our drop leg, all the way out is going to be 68 inches long for that full extension. If we have the screw run out all the way so the jack is all the way up, but no drop there, it's going to be 52 and a quarter inches. And that I'm getting by having the drop leg, just one position out so that you can still have your foot plate in place. So it's just measuring from this bottom lip on the drop leg, to the top of the jack with one notch in there. Whenever this is fully retracted, measuring from the same point, so the screw is all the way in, it's going to be 32 and three quarter inches.
So that gives us a total travel of 35 and three quarter inches.And 16 of those inches come from our drop. We can adjust that drop leg. I'll come around and show you guys. By pulling the pin, this is included with our landing gear, and these are in inch increments here. So it should get you back to operational so you can enjoy the rest of your vacation with no issues and get that fifth wheel leveled out and stabilized again. Now, if you need the follow leg, that's going to have the same measurements as this one. That's also available here at etrailer.com sold separately. You can find that using part number LC119101, or one zero one. But that's going to do it for our look at the replacement lead leg for the venture fifth wheel RV landing gear..
Customer Satisfaction Score:
90% were satisfied with this product
10% of customers were not satisfied
Ratings & Reviews
Brad
3/8/2024
Working great trailer levels faster and much quieter. The old jacks were binding and causing leveling system to struggle trying to auto level.
Bill
12/24/2025
One year later and working perfectly!
Lazer S.
12/24/2025
Steve G.
8/14/2021
After over a year my landing Jack is working perfectly no complaints. Neither the old Jack or new one has grease jerks to lubricate the gears so once a year I remove the Jack cover on top and spray chain lubricant on the gears and let it run down to the threaded shaft , the jacks run smooth now all the time
Eric S.
11/2/2023
After a year protect has held up great still satisfied
Mike L.
11/15/2023
Jenny N.
7/7/2023
This leg is meant to be a replacement for the Lippert Components Venture 5th Wheel RV landing gear. As long as your outer tube is 29.50 inches long then it will work for you. You would also want to measure the distance between the inside brackets as shown in the Q an A below.
Helpful Links
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Steven
8/16/2025
Working flawlessly. I appreciate the whole etrailer team that helped me. Thank yall very much. I will definitely contact you if and when I need trailer parts in the future.