Replacement Wheel Studs for 6k Rated Trailer Hub with 6 Lug Bolt Pattern

Question

Question:

Hi... I have a dual axel trailer with 6000lbs per axel. Hub is 6 lug 5 1/2 inch hub with aluminum wheels. would you know which wheel studs would work for them? I also like to use the acorn stainless steel nuts for them. I dont want the studs to be too long for the acorn stainless steel nuts. Trailer is out of state at this time and I cant not measure the dimension. I do have a zoomed photo of the trailer wheel. Hope it helps.

asked by: Tom

0

Expert Reply:

It's hard to say for certain which studs you'd need. But there's a great chance you have a 6 lug Dexter hub like the part # 8-213-5UC1 which uses the replacement studs part # 7-122. This is a 1/2 inch diameter stud that measures 2 inches in length.

For a 1/2 inch stainless steel acorn lug nut we have the part # KALN1375S which would work well.

expert reply by: Jameson C

0

Answer 1

Hey Mike, We sell replacement studs in single or multiple quantities depending on the specific sizing. For a 3,500lb trailer hub you most likely need the #DE52GR but I recommend punching one of your current ones out and comparing. The #DE52GR is…

view full answer...

Answer 2

I definitely get where you're coming from, and fortunately we have a pretty cost-effective solution for you with the stainless steel lug nuts. These are slightly more than the standard chrome plated lug nuts so you won't be shelling out too…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hi Donny; after looking at several videos of the trailer it does appear to have a 6 on 5-1/2 bolt pattern with ST225/75R15 tires. The Goodyear Endurance ST225/75R15 Radial Tire w/ 15" Eagle Aluminum Wheel #GY97QB will be a direct fit.

view full answer...

Replacement Wheel Studs for 6k Rated Trailer Hub with 6 Lug Bolt Pattern

Product Page this Question was Asked From

Continue Researching