Will # JET-01 Cover Fit etrailer Electric Jack 3500 lb Capacity?

Question

Question:

Will this Jet-01 cover fit your e-trailer electric jack w/footplate #3.5k capacity?

asked by: Tony K

0

Expert Reply:

The Vinyl Cover with Drawstrings for Stromberg Carlson Electric Jacks # JET-01 will fit the Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black # EJ-3520-BBX or White # EJ-3520-WBX but it will be a little big. I recommend the Ultra-Fab Protective Cover for Electric A-Frame Jacks # UF38-944020 instead as it will be a better fit.

expert reply by: Jason S

0

Answer 1

Yes, the Vinyl Cover with Drawstrings for Stromberg Carlson Electric Jacks #JET-01 will also fit the Stromberg Carlson Electric Trailer Jack #JET-5000.

view full answer...

Answer 2

What you mentioned is not fixable but if you bought this less than a year ago it would be covered under warranty most likely. Who did you buy it from and how long ago? If you need to purchase a new electric tongue jack I would highly recommend the…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 5

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 6

According to the Lippert Service Manual for the Lippert Electric Trailer Jack #LC285318. "Maintenance 1. Before each use, inspect the Power Tongue Jack and replace if bent or damaged. 2. If wiring is connected to battery terminal, inspect at…

view full answer...

Answer 7

When replacing your trailer's equalizer and shackle straps it's important to first measure the hole spacing of the current equalizer and shackle straps. The suspension needs to be able to travel back and forth as you go over bumps and when…

view full answer...

Answer 8

Thank you for providing the picture. However you hit that wood it managed to shove the one side up so far it pushed the other side into that position which prevented your wheel from coming back down. I wouldn't say something was necessarily…

view full answer...

Answer 9

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 10

Yes, the vast majority of a-frame trailer jacks use the same bolt pattern which is 3" apart on center. Therefore you should have no problems whatsoever using an electric a-frame trailer jack on your T@B 320 S teardrop camper. For this, I…

view full answer...

Answer 11

I spoke with my contact at Lippert and he confirmed that the Lippert Components Power Tongue Jack 1817941 #LC285318 can be rotated to be best orientated for you. The jack can be un-bolted, rotated, and reinstalled.

view full answer...

Answer 12

The Curt Hitch Ball Holder and Tightening Tool for Ball Mounts #C45007 will work well with the Curt Solid Ball Mount for 2" Hitches #C45313. The platform is the standard 2-1/2 inches wide. I recommend the hitch ball #A-90 for a 2 inch ball or…

view full answer...

Will # JET-01 Cover Fit etrailer Electric Jack 3500 lb Capacity?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching