Wiring Instructions for the Tradesman Vaquero Hydraulic A-Frame Trailer Jack
Updated 10/30/2025 | Published 10/02/2025
Question:
Looking for install instructions. Mainly looking for wiring setup requirements. Current electric jack has a 7 way plug for power. I assume Ill need a battery setup for this.
asked by: Uriah J
Expert Reply:
Hey Uriah, thanks for reaching out!
The Tradesman Vaquero Self-Contained Hydraulic A-Frame Trailer Jack # ST86FR will work best if it's hardwired to a battery on your trailer, but you can also hardwire a 7-Way plug and lead like part # H20043 and just plug that into your truck socket when you need to operate the jack.
If you look at the motor head on you'll connect the 12V power wire to the terminal on the left, and the negative wire to the middle terminal (see attached photo).
What kind of trailer will you be using this on?
(click to enlarge)
Product Page this Question was Asked From
Tradesman Vaquero Self-Contained Hydraulic A-Frame Trailer Jack - 26" Lift - 7,000 lbs
- Trailer Jack
- Dump Trailer
- Enclosed Trailer
- 5th Wheel Trailer
- Gooseneck Trailer
- Utility Trailer
- Side-Mount Jacks
- 6001 - 7000 lbs
- Hydraulic Jack
- 26 Inch Lift
- Bolt-On
- With Rectangle Foot
- Stillwell
more information >
Continue Researching
- Shop: Complete Bearing Kit with L44649 Inner/Outer Bearings and 10-9 Grease Seal Fits 1.063" Spindles
- Search Results: trailer leaf springs
- Shop: Tradesman Vaquero Self-Contained Hydraulic A-Frame Trailer Jack - 26" Lift - 7,000 lbs
- Search Results: trailer tires and wheels
- Search Results: dutton~lainson trailer jack
- Search Results: trailer brakes
- Search Results: free backing trailer brakes
- Shop: Gooseneck to 5th Wheel Trailer Coupler Adapter - Round - 30K
- Video: Review of Stillwell Trailer Jack - Tradesman Vaquero Self Contained Hydraulic A Frame - ST86FR
- Video: Review of RV Designer White Weatherproof GFI Outlet Cover - RD34FR
- Shop: Offset Trailer Spare Tire Mount by Dutton-Lainson
- Search Results: equalizer
- Search Results: outlet
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Self-Contained Hydraulic Trailer Jack - Square Tube - 24-1/4" Lift - 12,000 lbs - Bolt-On
- Shop: etrailer Hydraulic Trailer Brakes - Uni-Servo - Dacromet - 10" - Left/Right - 3.5K
- Shop: RV Designer Weatherproof Dual Outlet w/ Snap Cover Plate - White
- Q&A: Why Would Trailer Breakaway Charge Status Stay on Charge if Battery is Charged Already
- Q&A: Looking for a Replacement Handle for a Knott Autoflex Hand Winch
- Video: How to Install Your etrailer Self-Contained Hydraulic Jack - Utility Trailer
- Video: Checking Out the etrailer Enclosed Trailer Transition Plate
- Shop: Lift Assist
- Video: What to Know About the Backing Plate for Tandem Axle Trailer Fender
- Q&A: Does Optronics Over 80 Inch Rectangular Submersible Light Include any Mounting Hardware
- Shop: Brake Controller
- Video: 1004 Incandescent Light Bulb Feature Review
- Q&A: Replacement Trailer Hub for the TDE 46205 with Galvanized Finish
- Video: All You Need to Know About the Pollak HD, 7-Pole Round Pin Connector w/Cable Guard
- Q&A: Wiring Diagram For EOH Actuator Adapter
Jon G.
10/30/2025
Hey Uriah, how did the wiring setup go with the hydraulic A-frame jack? Did you end up using the 7-way plug or wiring it straight to a trailer battery? Your update could make it easier for the next person working on the same setup.