Electric Brake Compatibility on a Boat Trailer
Published 05/16/2018
Products Featured in This Question
Question:
Electric brakes on a boat trailer are able to be used without much issue at all. There obviously is an issue with water and electricity, so it is recommended to disconnect the trailer connection when your trailer is being submerged for launch. A few seconds after pulling out of the water, you can connect your wiring without any issues and have the functioning braking system that is easier to maintain. Many boat trailers are moving to electric systems. I do recommend using dielectric grease # 11755 on your connection points to keep moisture and debris out of the connection as much as possible. The heat shrink around the butt connectors is needed to keep the moisture out of the connection points and gives it a water tight seal. The electric brakes have the ease of use with a brake controller as you stated. I almost always recommend the Tekonsha Prodigy P3 # 90195 for a controller because of its features. The proportional braking, manual override, constant diagnostics, and ease of use with the LCD screen that takes codes out of the equation is an extremely nice feature. For your trailer, you can use the Epicord 7-Way Molded Trailer Plug with Junction Box - 10' Long # 277-000141 to get the electrical functions and then add # 10-2-1 wiring to your electric brake assemblies. Ring terminals like # 44-5310A make these electrical connections easy.
asked by: Jason W
Helpful Expert Reply:
Electric brakes on a boat trailer are able to be used without much issue at all. There obviously is an issue with water and electricity, so it is recommended to disconnect the trailer connection when your trailer is being submerged for launch. A few seconds after pulling out of the water, you can connect your wiring without any issues and have the functioning braking system that is easier to maintain. Many boat trailers are moving to electric systems. I do recommend using dielectric grease # 11755 on your connection points to keep moisture and debris out of the connection as much as possible. The heat shrink around the butt connectors is needed to keep the moisture out of the connection points and gives it a water tight seal.
The electric brakes have the ease of use with a brake controller as you stated. I almost always recommend the Tekonsha Prodigy P3 # 90195 for a controller because of its features. The proportional braking, manual override, constant diagnostics, and ease of use with the LCD screen that takes codes out of the equation is an extremely nice feature.
For your trailer, you can use the Epicord 7-Way Molded Trailer Plug with Junction Box - 10' Long # 277-000141 to get the electrical functions and then add # 10-2-1 wiring to your electric brake assemblies. Ring terminals like # 44-5310A make these electrical connections easy.
Product Page this Question was Asked From
Dielectric Grease for Electrical Connectors, 2 oz.
- Accessories and Parts
- Trailer Wiring
- Wiring
- Dielectric Grease
- LubriMatic
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: boat trailer electric brakes
- Search Results: 7 pin trailer connector
- Search Results: wiring
- Search Results: bearing buddy
- Search Results: trailer spring kit
- Search Results: springs
- Search Results: electric brake wiring
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Q&A: Can Electric Brakes be Used on Boat Trailer
- Shop: SuperSprings Custom Suspension Stabilizer and Sway Control Kit
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Wiring
- Video: etrailer Rust-Resistant 4-Leaf Slipper Spring for 4,300-lb Trailer Axles Review
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: How to Tell the Weight Rating of a Trailer Axle
- Shop: etrailer 7-Way RV Style Connector with Molded Cable - Trailer End - 6' Long - RV Standard
- Shop: Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
- Shop: etrailer Rust-Resistant Electric Trailer Brakes - Dacromet - 12" - Left/Right Hand - 5.2K to 7K
- Shop: Suspension Enhancement
- Q&A: Difference Between 3 and 4 Leaf Spring Stack for 3,500 Pound Axle
- Q&A: Can a 4-Leaf Trailer Leaf Spring be Used in Place of a 3-Leaf Spring
- Q&A: Is it Ok to Replace Factory Leaf Springs With a Higher Capacity Option?
- Q&A: Replacing Trailer Leaf Spring With 25-1/2" Measurement Bolt Hole To Bolt Hole
- Q&A: Is Bushing Required on Open Eye End of Slipper Spring
- Q&A: Can I Use Heavier Rated Leaf Springs on Trailer Without Causing Damage
- Video: etrailer 7 Way Upgrade Kit With Junction Box Installation
- Video: Hands-On with the Dexter Premier Disc Brake Kit
- Video: Let’s Check Out the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles
Jason W.
5/16/2018
Electric brakes on a boat trailer are able to be used without much issue at all. There obviously is an issue with water and electricity, so it is recommended to disconnect the trailer connection when your trailer is being submerged for launch. A few seconds after pulling out of the water, you can connect your wiring without any issues and have the functioning braking system that is easier to maintain. Many boat trailers are moving to electric systems. I do recommend using dielectric grease # 11755 on your connection points to keep moisture and debris out of the connection as much as possible. The heat shrink around the butt connectors is needed to keep the moisture out of the connection points and gives it a water tight seal. The electric brakes have the ease of use with a brake controller as you stated. I almost always recommend the Tekonsha Prodigy P3 # 90195 for a controller because of its features. The proportional braking, manual override, constant diagnostics, and ease of use with the LCD screen that takes codes out of the equation is an extremely nice feature. For your trailer, you can use the Epicord 7-Way Molded Trailer Plug with Junction Box - 10' Long # 277-000141 to get the electrical functions and then add # 10-2-1 wiring to your electric brake assemblies. Ring terminals like # 44-5310A make these electrical connections easy.