Distance from Plate to Pin Hole on Pro Series Detachable Footplate # PS1400700340

Question

Question:

Re: Pro Series detachable Foot Plate Part# 1400700340 My jack has a hole that starts about 3/4 in above the bottom edge. What is the distance in this Foot Plate from the plate to the hole?

asked by: Eileen

0

Expert Reply:

I went out to the warehouse and was able to measure the distance from the base plate to the pin hole on the Pro Series Detachable Footplate # PS1400700340. The distance is right at 3/4 inches so you should have no problem using it with your existing jack as long as it also has 2 inch diameter tubing.

I have included an image labeled with this dimension for you to review.

expert reply by: Chris R

0

click to enlarge

Answer 1

I think the Fulton F2 Swing-Up Jack is a good choice. The model for 4 - 5" frames is #F1413140334. The 1600 lb. tongue weight rating is much more than you need, but won't affect the function of the jack. The height will work and it will get…

view full answer...

Answer 2

You will need to choose a jack whose capacity exceeds the fully loaded and ready to tow tongue weight of your trailer. Typically trailer tongue weight is 10-15 percent of the weight of the trailer. This means that when loaded to maximum, your tongue…

view full answer...

Answer 3

Yes, about 99 percent of A-frame jacks use the same mounting pattern. The holes are generally 3 inches apart on center though it can vary ever so slightly which is why some jacks have slotted holes.

view full answer...

Answer 4

The Round A-Frame Trailer Jack #TJA-5000S-B has mounting holes that are elongated. The actual holes are 3/4 inch long and 7/16 inch wide. That gives you a minimum of 2-1/2 inches or maximum of 3-3/4 inches to the nearest or farthest part for…

view full answer...

Answer 5

Yes, basically all A-frame trailers are going to have the same bolt pattern for installing a trailer jack. Typically the jacks have mounting holes that are somewhat slotted too to help with some variances. The bolt pattern you mentioned having on…

view full answer...

Answer 6

The bolt holes on the etrailer Round, A-Frame Jack, item #TJA-5000S-B, triangle mounting flange are 3 inches from center of one hole to the center of the next hole. They are equally spaced apart and they are elongated for easier installation. A-Frame…

view full answer...

Answer 7

I went out to our warehouse to take a look at the Buyers Products A-Frame Jack #3370091265 referenced in your question. I measured a height from the mounting bracket up to the top of the tube (before the handle) of just about 9-1/2 inches. I have…

view full answer...

Answer 8

The mounting hole dimensions of A-frame jacks are a standard 3 inches apart on center, so you will need to weld your new jack on. I highly recommend the etrailer Round, A-Frame Jack #TJA-5000S-B, which has a 5,000 lb capacity and will give you…

view full answer...

Answer 9

The Phoenix Electric Trailer Jack with Remote #UF38-944055 has a multiple mount hole pattern. This pattern allows you to position the jack so the motor faces the front of the A-Frame, or it can be rotated so that the motor faces the drivers side of…

view full answer...

Answer 10

Hey Robert, I've attached a diagram below showing the dimensions/spacing of the mounting holes for the etrailer Round A-Frame Trailer Jack #TJA-5000S-B. If you need any other measurements just let me know and I'd be happy to check for you.

view full answer...

Answer 11

Since Sport Masters has gone out of business, there are no longer replacement parts available. Unfortunately, this means the only option is to replace the entire cover. For a soft cover replacement I recommend the following: -Access TonnoSport Soft,…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Distance from Plate to Pin Hole on Pro Series Detachable Footplate # PS1400700340

Continue Researching