Mounting Hole Dimensions And Spacing For The etrailer Round A-Frame Trailer Jack # TJA-5000S-B

Question

Question:

etrailer Trailer Jack - TJA-5000S-B whats the bolt pattern dimensions and hole IDs?

asked by: Robert E

0

Expert Reply:

Hey Robert,

I've attached a diagram below showing the dimensions/spacing of the mounting holes for the etrailer Round A-Frame Trailer Jack # TJA-5000S-B. If you need any other measurements just let me know and I'd be happy to check for you.

expert reply by: Kevin C

0

Hole Dimensions
(click to enlarge)

Answer 1

There are a few solutions for your tailgate to clear the jack on your trailer. I recommend to use a longer ball mount like #D-26, that would move the trailer back further away from the truck and give you clearance you need. If you know what size the…

view full answer...

Answer 2

We have a really great trailer jack replacement for what you have with the etrailer Sidewind Jack part #TJA-5000S-B. This is a sidewind jack like what you have but as you can see in the attached install video it can install with the handle on the…

view full answer...

Answer 3

The Phoenix Electric Trailer Jack with Remote #UF38-944055 has a multiple mount hole pattern. This pattern allows you to position the jack so the motor faces the front of the A-Frame, or it can be rotated so that the motor faces the drivers side of…

view full answer...

Answer 4

Yes, about 99 percent of A-frame jacks use the same mounting pattern. The holes are generally 3 inches apart on center though it can vary ever so slightly which is why some jacks have slotted holes.

view full answer...

Answer 5

I went out to our warehouse to take a look at the Buyers Products A-Frame Jack #3370091265 referenced in your question. I measured a height from the mounting bracket up to the top of the tube (before the handle) of just about 9-1/2 inches. I have…

view full answer...

Answer 6

The Round A-Frame Trailer Jack #TJA-5000S-B has mounting holes that are elongated. The actual holes are 3/4 inch long and 7/16 inch wide. That gives you a minimum of 2-1/2 inches or maximum of 3-3/4 inches to the nearest or farthest part for…

view full answer...

Answer 7

I went out to the warehouse and was able to measure the distance from the base plate to the pin hole on the Pro Series Detachable Footplate #PS1400700340. The distance is right at 3/4 inches so you should have no problem using it with your existing…

view full answer...

Answer 8

The mounting hole dimensions of A-frame jacks are a standard 3 inches apart on center, so you will need to weld your new jack on. I highly recommend the etrailer Round, A-Frame Jack #TJA-5000S-B, which has a 5,000 lb capacity and will give you…

view full answer...

Answer 9

The bolt holes on the etrailer Round, A-Frame Jack, item #TJA-5000S-B, triangle mounting flange are 3 inches from center of one hole to the center of the next hole. They are equally spaced apart and they are elongated for easier installation. A-Frame…

view full answer...

Answer 10

Yes, basically all A-frame trailers are going to have the same bolt pattern for installing a trailer jack. Typically the jacks have mounting holes that are somewhat slotted too to help with some variances. The bolt pattern you mentioned having on…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Mounting Hole Dimensions And Spacing For The etrailer Round A-Frame Trailer Jack # TJA-5000S-B

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching