Replacement Hardware Size for the Draw Tite Hitch 75547

Question

Question:

I removed the hitch from my other CRV and lost the bolts to install it on my new Honda CRV. Hitch number 75547. Can you tell me what size installation bolts I need?

asked by: Glenn F

0

Expert Reply:

The bolt sizes that come with the part # 75547 are M10X1.25X30 CL8.8. You can order all new hardware from us with part # RHK too. You would need to select Draw Tite on the drop down menus and then enter the part number 75547.

expert reply by: Jameson C

0

Answer 1

The Draw-Tite trailer hitch receiver, part #75547, uses 4 hex bolts that are M10 X 1.25 X 30. However, you shouldn't tap the threads uness you absolutely have to as a last resort. I highly recommend cleaning them before tapping them. I've…

view full answer...

Answer 2

In order to order the replacement hardware for your Draw-Tite Hitch #75547, you simply go to the Replacement Hardware Kit for Trailer Hitches #RHK product page and enter "75547" in the hitch item number box and select "Draw-Tite"…

view full answer...

Answer 3

I have attached the installation instructions of the EcoHitch Hidden Trailer Hitch Receiver part #306-X7291 for a 2008 Honda CR-V to this answer page for you. In regards to installation, this is a bolt-on fit with a very clean finished install look.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Replacement Hardware Size for the Draw Tite Hitch 75547

Products Featured in This Question

Continue Researching