To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.
Features:
Specs:
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side interior trim panels in your rear cargo area. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery and insert the provided fuse.
Once installation is complete, the 4-way flat connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A ModuLite power module is built into this T-One connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of your trailer. This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
California residents: click here
Easy installation!
Easy product selection, fast shipping, great service. Thank you!
The wiring takes some time to do it rite ( about 3 hrs.) only because you have to take off the rear interior side panels to get to the wiring for the lights and run a single wire from the rear of the car to the front of the car.The instructions are straightforward and easy to follow.
A very nice and knowledgable lady, Cheryl, hepled me find a hidden wire connector on my Lexus by phone on Saturday afternoon at 4:00 pm. Where else can you find help like that?
Excellent product! All of the wires were the correct length and it plugs in as advertised. It took me about 4 hours to install but I have not worked on a car in years and I removed more interior panels than I should have for the installation. The biggest issue was getting to the factory wiring unplugged. The plugs were behind a panel that I did not remove. I would highly recommend this product.
I was impressed with the quick delivery and the kit contained everything needed for installation. All of the wiring was sized perfectly for a RX330 and installation (with re-assembly) took about 3 hours. I ran the power wire on the inside of the car (driver side under the step-in covers) and used an electrician's fish tape to help pull the wire from front to back. I definitely recommend this kit for other Lexus RX330 owners.
Thank you for following up. Your wiring harness is still working great.
The hitch was a perfect fit, installation was straight forward. The wire harness was moderately difficult to install without having a lift to get under the vehicle but still pretty straight forward. I ordered the hitch on a Monday, and it showed up at my house 4 pm Wednesday. etrailer was helpful answering my questions regarding what parts to order. I saved about $300 doing this job myself.
Will is great and the whole experince was tremendous. Thank you!
Took awhile to get installed but the YouTube video was extremely helpful and straightforward. Worked first try too!
Works very well! I'm satisfied
The wiring harness brake lights did not work. I called in 7/18 and got a replacement and discussed the need to have it by 7/23 because I need to connect a trailer on 7/24. Order processed on 7/19, Did not leave Salt Lake until 7/22 to Colorado. Left Colorado 7/23. My trip plans with the trailer appear to be completely ruined.
Very Clean install. Installation video was concise and easy to follow. Between the Trailer, trim cutout, and electrical install with Item #118252, I was done start to finish in about three hours.
The hitch fit on my 2005 Lexus RX330 with no problems. It took only about 15 minutes to install by myself. (no helper) . The wiring harness ( Part # 118478) installed as advertised. The vidio provided by e.trailer was a big help. All lights worked with no problems.
The hinges I purchased were very well built and have performed perfectly. I am very satisfied. I used them vertically and they hold up great.
Excellent product and delivery
I ordered and installed a trailer hitch complete with wiring on our Lexus SUV last year.
As it was made specially for the vehicle, it was a perfect fit using the existing frame holes. I watched a couple videos for the wiring harness install, then proceeded easily to hook up the harness under the length of the vehicle and used the supplied connectors. You need to be able to jack up the car with a floor jack and safety stands in the rear first. Then let the rear down, jack up the front and finish securing the harness along the framing. Then let the car down and finish the simple hook up to the battery ( Of course if your battery is in the rear you will be done faster. ) I like the product, enjoyed doing the install myself.
I recently purchased my third trailer hitch from e-trailer for personal use. The hitch is relatively easy to install, but the wiring can and could be more difficult,. But with e-trailer you tube instillation for different cars, makes it almost a joy.
However, I don't have access to a lift, and must do the driveway thing. I also did a modification with the wiring. I measured, and remeasured a couple of times to see if it could a better looking and fixed position rather than having the tell tale appearance with the colored wiring hanging out the tailgate.
I double wrapped that wiring with electrical tape and used the plug that is behind the wheel, and about ten inches forward of the hole with the power wire.
I removed the plug, cut a hole 1/8 X 3/8, and then cut a line from the outer edge of the plug to that hole. That size worked perfectly for the glued together four wires as a single flat wire. then I went down thru it with the cut toward the front of the car so as to not create a gap in the plug that could widen with the pressure of the wire(s). I then went toward the back of the top inf the hitch bracket where there was a indentation with a fixed small split rubber hose to minimize wiring abrasion, then over toward the center of the hitch.
I'm now waiting for the mounting plate for the small bracket (which I have), mounting in a fixed position where it will not be subject to items such as tree limbs etc, and other road debris...won't bother the wiring.
Also, when wiring to the battery post, with the movie clip as suggested, there's a small little 1/2 X 1/2 piece to be broken/cut out of the cover plate for the positive end of the battery cable...otherwise the cover won't snap down on both wires.
Also saw a previous comment about the receiver part being a nuisance bumping the leg. From previous (e-trailer) hitches, I have a receiver light that is much softer than the hitch receiver, and has a rubber foam surround. The plastic light is much less injurious.
The hitch and wiring is no less well engineered.
Thank you for your ability for shipping.
I ordered the hitch about 1530 one afternoon, and received the hitch the next day around 1430...less than one day via UPS...excellent service.
Written instructions are INCOMPLETE! WATCH THE VIDEO!
I purchased this brand over the Curt product simply because the written instructions were clearer. Or so I thought.....(See "Installation Details" PDF at the end of the respective product descriptions and compare for yourself).
During installation, I found an additional plug on the RH side of the vehicle that wasn't mentioned in the instructions. Not knowing what to with it, and being in somewhat of a hurry, I let it be. And then I forgot about it.
After installation I asked my wife to check all the lights on the trailer as I hit the switches in the car (Me: "Right turn?" She: "Yup!", etc, etc), so I thought all was well.
So we hooked-up the trailer and headed-out.
About an hour later we were pulled over by one the "Boys In Blue" who said the brake lights on our trailer didn't work. "Can't be", I thought to myself. Sure enough- nothing! (Thankfully we were close to home again, he seemed to be sympathetic and understanding, and so he let us go w/o giving us a ticket.).
When we got home I looked at the instructions again, and I did everything right!
However, the installation video (around the 2:30 mark), AS WELL AS THE INSTRUCTIONS FOR THE CURT PRODUCT, explain where this other/second plug gets connected. Trust me, it's not immediately apparent where it goes, but had I had PROPER INSTALLATION INSTRUCTIONS I wouldn't have made this mistake in the first place!
Everything seems to work fine now, but shame on T-One for providing incomplete instructions (and shame on me for forgetting about that plug).
The hitch fits perfectly. Arrived without a scratch on it. I installed it myself (with the help of my floor jack) and was easy. The only "hitch" was that after I had almost completed the install,, I saw that if I had tightened the bolts all the way, the spare tire might have been pinched by the hitch cross member and maybe not been able to be freely lowered. So I had to loosen the bolts and pull the tire cover clear while I tightened the bolts to complete install. The wiring took longer than the video shows only because of access. But running it forward to the battery was no problem. The videos were very helpful, though. And, everything works perfectly. Thanks, E-Trailer.
Not the right harness for 09 Lexus RX350. Had to order OEM harness from dealer which was plug and play and easy install
Katrina D.
7/8/2023
This harness will only fit if your 2009 Lexus RX350 without a factory tow package. Can you please confirm whether you have the factory tow package or not?
Hi Mike . . . received the 'hitch' on Saturday, March 14th, 2015.
Everything in the box was complete. It took me about 45 minutes to install - there were no problems except I had to borrow a 'breaker bar' from my neighbor to remove the two 'pull hooks' that were attached to my frame from the factory. I was amazed how easy the frame mounted with the provided brass bolts fitting EXACTLY into the holes in the frame.
The instructions were perfect! I am 74 yrs old and used a heavy duty box to hold up the other end of the hitch while I attached the left side - a little easier to get to the frame than the 'exhaust' side.
The 'wire harness' was another story. The instructions were very tiny and I could not grasp how to hook up the various electrical connections. . . Oh well, I will pay out $80 to have the electrical mounted by our local garage in town.
I would still give eTRAILER an 'A' for a excellent, sturdy, attractive hitch that will do a great job for me. Many thanks to Mike S for his assistance in purchasing this item. Give him a raise!!!
Bought a plug and no cutting or other wiring problems trailer wiring kit for my auto trailer hitch. I simply gave them my auto info and got the right kit. Followed a utube video and everything worked perfectly. Jumped into the car and headed to Arizona with lights blazing. Thanks etrailer.
Great company. Had a question,Sal answered the phone. Problem solved. Very knowledgeable. Couldn't be more pleased with the shipping,service.
Tom
11/17/2018
Flawless
The hitch was on in 15 minutes and fits perfectly and does not limit the spare tire at all. Nice design though I wish it did not stick out from the bumper, but there is no other way because of how the car is made. The wiring kit is great and well designed. Getting the panels off to get to the vehicle wiring is the biggest hassle and the double sided tape did not stick. But it all hooked up and works great. Thanks etrailer for a great product!
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jw
10/18/2014
It works as advertised. No problems after a years use.