Headlight Protection Film Specs:
Features:
Apply LampGard to your headlamps, fog lamps, turn-signal lights or parking lights and never worry about scratching, cracking or pitting again. This tough, UV-resistant cover installs in seconds directly to the lamp surface for complete protection.
More Information >Headlight Protection Film Specs:
Features:
Apply LampGard to your headlamps, fog lamps, turn-signal lights or parking lights and never worry about scratching, cracking or pitting again. This tough, UV-resistant cover installs in seconds directly to the lamp surface for complete protection.
More Information >Videos
for Headlight Protection Film
Help Articles
for Headlight Protection Film
Expert Answers
for Headlight Protection Film
A trailer axle like part #e25GR does not have a designated speed rating. The tires that you use with this axle will be the determining factor for a speed rating. For example, the Kenda Karrier Radial Trailer Tire #AM35351DX is commonly used with…
view full answer...The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.
view full answer...Yes, the etrailer SD Non-Binding Tow Bar for Blue Ox Base Plates #e47ZR would have enough adjustability between the 1-1/2" shank rise/drop and the 3" of tilt to meet your 4" difference.…
view full answer...The Blue Ox Acclaim Non-Binding Tow Bar #BX4330 is compatible with Blue Ox base plates that are between 23" and 30" apart on center. Since you're measuring 34" on…
view full answer...Before deciding on a trailer to tow with your 2014 Ford Fusion, knowing the towing limitations of your vehicle will be an important factor. In the owner's manual for the 2014 Fusion, it lists the maximum trailer weight of all…
view full answer...When we installed the Curt Hitch #C12091 on a 2015 Ford Fusion we found that from the top of the hitch opening down to the ground it measured 11-1/2 inches. From the bottom of the hitch to the ground would be about 10 inches. I attached an install…
view full answer...It is not recommended to reinstall the lower body fascia with the Curt Class II Trailer Hitch, #C12091, on your 2013 Ford Fusion Titanium because of the final position of the hitch once it is installed. It may be possible to mount the fascia with…
view full answer...You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever…
view full answer...I was able to track down the installation instructions for the EcoHitch Hidden Trailer Hitch Receiver #306-X7317 referenced in your question and have attached the images from the manual below. I have also sent you a separate email with the PDF file…
view full answer...The 16 inches of height that the Yakima SkyBox NX 16 Cargo Box #Y95AV that you referenced would be the height above the crossbars of your 2005 GMC Yukon Denali. I attached a review video for this cargo box for you to check out also.
view full answer...You will want the hitch to be set at the height that 1) allows the trailer to be level, and 2) allows you a minimum of 6 inches between the bottom of the trailer loft and the top of the bed rails. The fifth wheel hitches offer several inches of up…
view full answer...When adjusting the arms of the #BWRVK3305, you have the option of setting up so the king pin will sit 3 inches forward or 1 inch forward of the axle. I'd set it up at the tallest height, 18-3/4 inches above the floor of the truck…
view full answer...Filter Products (4)
Contact and Help
What our customers are saying:
Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast.
John
Mankato, MN