How Does Curt TriFlex NEXT Brake Controller Mount

Question

Question:

How do you mount the Curt Triflex Next brake controller? doesn't look like a regular bracket

asked by: Sam

0

Expert Reply:

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller # C24VV.

The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under your dash. Screws are also included and you can use them with the adhesive to mount the bracket under your dash. Then you'll simply slide in the TriFlex NEXT controller and that's it.

This type of bracket takes up less space than the normal U-shaped bracket most brake controllers come with, so you won't be losing any leg space in your cab. And so you can get a better idea of how it works, I have gone ahead and added photos showing the bracket and TriFlex NEXT # C24VV.

expert reply by: Kyle S

0

Curt TriFlex NEXT Brake Controller & Mounting Bracket
(click to enlarge)

Mounting TriFlex NEXT Under Dash
(click to enlarge)

Svaraman

2/2/2025

I need to purchase another mounting bracket for my Curt Triflex NEXT brake controller so I can use it in a second vehicle. I believe the part number for the bracket with the adhesive pads is 19297, but that part number isn't available on your website or on the Curt website. How do I buy a second mounting bracket?

Kate F.

2/4/2025

@Svaraman Hey there Svaraman, you were having a hard time finding the second bracket because we didn't have it on the site. I worked my magic and was able to get it added, you want the Replacement Mounting Bracket for Curt NEXT Brake Controllers # C24MJ. Did you need vehicle specific pigtail for the second vehicle as well? If so, send me over the year, make, and model and I will get you a part number.

Svaraman

2/4/2025

@KateF Thanks! FWIW, I was only able to find the bracket using your link. Searching for "C24MJ" or "19297" on etrailer.com yielded zero results so anybody else won't be able to find it. I was able to find the wiring harness I needed on my own. I ordered both. Thanks!

Kate F.

2/5/2025

@Svaraman Ya, when we add stuff to the site for some reason it's a little wonky the day of. If you ever need anything in the future Svaraman you know where to find us!

Answer 1

The factory harness to plug in a brake controller wiring harness on your 2007 Toyota Tacoma is located underneath and left of the steering column, taped to another harness near the emergency brake pedal. There will be a 5-pin connector that mates…

view full answer...

Answer 2

The Curt TriFlex Trailer Brake Controller part #C24VV is an excellent option for a 2008 Chevrolet Silverado when used with the Universal Wiring Adapter for Curt Trailer Brake Controllers part #C51515. The wires under the dash are already ran and…

view full answer...

Answer 3

If you have the factory tow package on your 2022 Honda Ridgeline, then you will just need the Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers #RED59FR for the Redarc Tow-Pro Liberty Brake Controller #RED24FR. In order to…

view full answer...

Answer 4

The calibration process of the Curt Spectrum #C51170 should only happen after initial installation and should be run before you plug in the trailer to your tow vehicle. You should have seen the green lights on the knob light up in a clockwise motion…

view full answer...

Answer 5

It sure will! A brake Controller isn't a vehicle specific item, you can install a brake controller in just about any vehicle. To swap the controller back and forth, you'll need a #7894 pigtail and a #TK5906 Replacement mounting bracket kit.…

view full answer...

Answer 6

Thanks for the pictures! I have exactly what you are looking for. We have a couple of mounting options for the control knob that can go inside inserts in your Subaru's dash. This will give you a clean factory look install. The Universal Mounting…

view full answer...

Answer 7

Hey Christa, so the Curt Triflex part #C24VV shouldn't be draining your battery since it should be going into a sleep mode when not in use. To cut power to it you would need to unplug it at the rear of the controller. There isn't a master…

view full answer...

Answer 8

Hey Wayne! Thank you for reaching out. The length on the main body tube for the Adjustable Width Trailer Hitch Receiver #C13702 is 51". What are you going to use the hitch for?

view full answer...

Answer 9

We can get you everything you need for towing with your 2017 Toyota Sienna XLE. By plastic shield, I believe you are referring to the appearance panel underneath the Sienna, and that will have to trimmed a bit in each of the hitches available for the…

view full answer...

Answer 10

It is not uncommon for a brake controller port to be taped up so that very well could be it. The 2-prong one is not it. Brake controller wiring has 4 functions, ground, power in, power out to the brakes, and input from the brake switch. If your 2007…

view full answer...

Answer 11

I have included photo that shows the location of the brake controller port on a 2007 Toyota Tacoma. We have not had a 2007 model that had a tow package to determine the plugs exact location for that model year. According to my contacts at Tekonsha,…

view full answer...

Answer 12

Yes, you can manually adjust self-adjusting brakes with a spoon like the drum brake spoon #W80630. If you let me know what is going on with your brakes I can try to help you troubleshoot why your brakes need to be adjusted.

view full answer...

How Does Curt TriFlex NEXT Brake Controller Mount

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching