Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…
Hey Bill, thanks for reaching out. I just went out to our warehouse and measured the Replacement Left/Curb Side Leg for etrailer and Ram Hydraulic Jack #e63VV. The outer tube is 4-1/2" square. The inner tube with the foot is 4".
Good question, Tina - you’re in the safe zone with the M-3 aluminum plate #M348FR. It’s 3/16 inch thick and fully welded across the piano hinge (some cheaper ones are just bolted instead of welded), so even with heavy mowers or small tractors, it…
Hey Jeff! It has more to do with the roof structure of a utility trailer than anything. As long as you have the proper bracing in place you'll be just fine installing the 13,500 Btu Advent Air RV Air Conditioner System #ADV95SR on your trailer.…
Hey Brandon! Yes, either M-3 transition plate (steel #M368FR or aluminum #M348FR) will do the job, but I’d go aluminum #M348FR since it’s easier to trim and won’t rust if water gets in that recessed area. Just mount it across the lower edge of the…
Kyle, the HomePlows like #ME53FR lift about 8" in travel mode, while the WingMan #ME35FR lifts closer to 10" thanks to its larger hydraulics. That’s plenty to clear curbs or the edge of your apron. If your slope’s steep, you’ll appreciate…
Lisa, the HomePlow #ME53FR uses a true hydraulic lift and power-angling system, so it can apply real down pressure when you hold the lower control. That’s the main advantage over the electric HomePlows like the ##ME28FR and #ME88FR, which only lower…
Hey Marty. Caliber lists the weight capacity for their Edge Glide XL Transition Plates item #CA47EJ as matching your trailer's ramp door. So whatever your ramp door capacity is is what transition plates will sport. The 4-pack has a combined…
Hello Dean, thanks for reaching out. We currently carry only the one transition plate, the etrailer Enclosed Trailer Transition Plate #e32JR. This is adjustable and has a maximum overall width of 82". it is made of steel. Sadly, we do not make…
I'd go with a double spring personally, Scott. These are typically going to be used on more heavy duty applications like your enclosed trailer with a pretty heavy door. In order to get a proper replacement though, you'd need measure the width…
Hey Tom! The Red Trimax King Pin Lock #TMX36RR and the Yellow Lock #TMX56RR are literally the same lock, just with different colors. I'm not sure why there's a price difference like that, but usually I tell people to take advantage of the…
Nick, absolutely. Many vanlifers wire the Velit 2000R 12V AC Unit #VE87QV so it runs while the alternator tops off the batteries. It keeps the living space cool while driving long stretches, and when you park, your bank’s already partly replenished.…
Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…
Hey Bill, thanks for reaching out. I just went out to our warehouse and measured the Replacement Left/Curb Side Leg for etrailer and Ram Hydraulic Jack #e63VV. The outer tube is 4-1/2" square. The inner tube with the foot is 4".
Good question, Tina - you’re in the safe zone with the M-3 aluminum plate #M348FR. It’s 3/16 inch thick and fully welded across the piano hinge (some cheaper ones are just bolted instead of welded), so even with heavy mowers or small tractors, it…
Hey Jeff! It has more to do with the roof structure of a utility trailer than anything. As long as you have the proper bracing in place you'll be just fine installing the 13,500 Btu Advent Air RV Air Conditioner System #ADV95SR on your trailer.…
Hey Brandon! Yes, either M-3 transition plate (steel #M368FR or aluminum #M348FR) will do the job, but I’d go aluminum #M348FR since it’s easier to trim and won’t rust if water gets in that recessed area. Just mount it across the lower edge of the…
Kyle, the HomePlows like #ME53FR lift about 8" in travel mode, while the WingMan #ME35FR lifts closer to 10" thanks to its larger hydraulics. That’s plenty to clear curbs or the edge of your apron. If your slope’s steep, you’ll appreciate…
Lisa, the HomePlow #ME53FR uses a true hydraulic lift and power-angling system, so it can apply real down pressure when you hold the lower control. That’s the main advantage over the electric HomePlows like the ##ME28FR and #ME88FR, which only lower…
Hey Marty. Caliber lists the weight capacity for their Edge Glide XL Transition Plates item #CA47EJ as matching your trailer's ramp door. So whatever your ramp door capacity is is what transition plates will sport. The 4-pack has a combined…
Hello Dean, thanks for reaching out. We currently carry only the one transition plate, the etrailer Enclosed Trailer Transition Plate #e32JR. This is adjustable and has a maximum overall width of 82". it is made of steel. Sadly, we do not make…
I'd go with a double spring personally, Scott. These are typically going to be used on more heavy duty applications like your enclosed trailer with a pretty heavy door. In order to get a proper replacement though, you'd need measure the width…
Hey Tom! The Red Trimax King Pin Lock #TMX36RR and the Yellow Lock #TMX56RR are literally the same lock, just with different colors. I'm not sure why there's a price difference like that, but usually I tell people to take advantage of the…
Nick, absolutely. Many vanlifers wire the Velit 2000R 12V AC Unit #VE87QV so it runs while the alternator tops off the batteries. It keeps the living space cool while driving long stretches, and when you park, your bank’s already partly replenished.…
Trailer door parts are essential for maintaining the safety and functionality of your trailer. Whether you're hauling horses or heavy equipment, these parts ensure smooth operation and protection. Consider the durability, ease of installation, and compatibility with your trailer when selecting parts.
Trailer door parts, like rubber bumpers, are built to withstand heavy use and harsh conditions. Many find them still in excellent condition after a year of regular use, even under the weight of horses or heavy equipment. They typically need replacement every 8-10 years due to sun exposure.
Most trailer door parts are designed for straightforward installation, though some may require drilling new holes to fit your specific trailer. It's important to check compatibility and be prepared for minor adjustments to ensure a perfect fit.
When selecting trailer door parts, consider the material quality, compatibility with your trailer, and the specific needs of your cargo. High-quality materials ensure longevity, while the right fit prevents issues like chipping or pulling away from the trailer.
Trailer door parts are designed to handle various weather conditions, from rain to intense sun. Rubber bumpers, for instance, maintain their integrity and protect your cargo even after exposure to the elements, making them a reliable choice for any climate.
Common issues include misalignment of pre-drilled holes and the need for additional mounting holes. However, these can be easily resolved with some adjustments. Ensuring the right fit and quality materials can prevent most problems, providing a smooth and secure operation.
Filters
