Trailer Door Parts - RV Designer

Good question, Tina - you’re in the safe zone with the M-3 aluminum plate #M348FR. It’s 3/16 inch thick and fully welded across the piano hinge (some cheaper ones are just bolted instead of welded), so even with heavy mowers or small tractors, it…

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

Hey Alan - you can absolutely use the M3 plate at the door-to-floor gap. Many folks run one on the outside edge and another inside for a totally smooth roll-through. The steel plate #M368FR gives you extra strength if you’re using pallet jacks or…

Hey Dylan - both M-3 plates measure 81-3/4 inches wide, so you'd need to trim off a little bit. The aluminum one #M348FR would be easier to trim, so I'd pick that over the steel one. The hinge runs the full width so you’ll still get solid…

Hey Robert, we have rubber lip seals for compartment doors on RVs with the part #SR92FR which is a 15 foot long section. Did yours fail over time or did it fall off?

Hey Dustin. I installed the Enclosed Trailer Transition Plate item #M368FR on a trailer here when we first got them in and you're good! That plate is single solid piece of steel. It's got a heavy duty piano style hinge that has been riveted…

Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…

Hey Kyle! That is correct. The Coleman-Mach Mach-C Everest has variable-speed cooling and an inverter-driven compressor. However, the Mach-C Everest uses a traditional wall thermostat instead of a remote control. It also works with both ducted and…

Hi Tim! The Triangle ST235/80R16 Radial Trailer Tire with 16" Aluminum Wheel - 8 on 6-1/2 - Load Range G #KE83JR comes with rubber valve stems (see included image). These come to us already put together and we do not have the ability to unmount…

I'd go with a double spring personally, Scott. These are typically going to be used on more heavy duty applications like your enclosed trailer with a pretty heavy door. In order to get a proper replacement though, you'd need measure the width…

Hello Robert, Yes, the only difference between the 2 is that the etrailer Enclosed Trailer Transition Plate #e32JR is quantity: 1, and the #e99RV is quantity: 2. Right now it looks like if you wanted a better deal to buy 2 of the #e32JR. It is times…

The correct replacement for an Atwood Water Heater GC6AA-9E is the Dometic RV Water Heater part #DMC74FR. This is a 6 gallon water heater that works with both gas and electric just like the one you have so it will be an exact match.

Good question, Tina - you’re in the safe zone with the M-3 aluminum plate #M348FR. It’s 3/16 inch thick and fully welded across the piano hinge (some cheaper ones are just bolted instead of welded), so even with heavy mowers or small tractors, it…

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

Hey Alan - you can absolutely use the M3 plate at the door-to-floor gap. Many folks run one on the outside edge and another inside for a totally smooth roll-through. The steel plate #M368FR gives you extra strength if you’re using pallet jacks or…

Hey Dylan - both M-3 plates measure 81-3/4 inches wide, so you'd need to trim off a little bit. The aluminum one #M348FR would be easier to trim, so I'd pick that over the steel one. The hinge runs the full width so you’ll still get solid…

Hey Robert, we have rubber lip seals for compartment doors on RVs with the part #SR92FR which is a 15 foot long section. Did yours fail over time or did it fall off?

Hey Dustin. I installed the Enclosed Trailer Transition Plate item #M368FR on a trailer here when we first got them in and you're good! That plate is single solid piece of steel. It's got a heavy duty piano style hinge that has been riveted…

Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…

Hey Kyle! That is correct. The Coleman-Mach Mach-C Everest has variable-speed cooling and an inverter-driven compressor. However, the Mach-C Everest uses a traditional wall thermostat instead of a remote control. It also works with both ducted and…

Hi Tim! The Triangle ST235/80R16 Radial Trailer Tire with 16" Aluminum Wheel - 8 on 6-1/2 - Load Range G #KE83JR comes with rubber valve stems (see included image). These come to us already put together and we do not have the ability to unmount…

I'd go with a double spring personally, Scott. These are typically going to be used on more heavy duty applications like your enclosed trailer with a pretty heavy door. In order to get a proper replacement though, you'd need measure the width…

Hello Robert, Yes, the only difference between the 2 is that the etrailer Enclosed Trailer Transition Plate #e32JR is quantity: 1, and the #e99RV is quantity: 2. Right now it looks like if you wanted a better deal to buy 2 of the #e32JR. It is times…

The correct replacement for an Atwood Water Heater GC6AA-9E is the Dometic RV Water Heater part #DMC74FR. This is a 6 gallon water heater that works with both gas and electric just like the one you have so it will be an exact match.