Hey Teo, we have a solution for you but we don't have any harnesses that work as both a tow bar lighting kit and a trailer wiring kit. So what you'd want is the Curt part #C96JR for the tow bar lighting and then for the trailer wiring…
The Curt front hitch part #31199 is a fit for your 2WD 2004 Nissan Titan. If you check out the install picture I attached you will see that it does not extend out past the front bumper of a vehicle it is installed on.
Hello Dean, thanks for reaching out. We currently carry only the one transition plate, the etrailer Enclosed Trailer Transition Plate #e32JR. This is adjustable and has a maximum overall width of 82". it is made of steel. Sadly, we do not make…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Between those two color choices the black one would most likely be the ground wire. However, if you hook it up with the black as the ground and it does not work I would recommend trying the red wire. Also, you should trace both of these wires back on…
I have included a picture that shows the measurements needed for a spindle, bearings, seals, faces, and hubs. The spindle measurements are labeled A through F. A is the spindle shaft diameter B is where the grease seal sits C is where the inner…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Hey Colsen. I have some bad news for you. There are no hubs with bearings item #LM48548 and M12649 available. I checked elsewhere and there isn't a hub I can find anywhere that uses those bearings. The only solution I have for you is to replace…
You will first want to check the fuses on your tow vehicle. Some vehicles could have fuses for operating the turn signals and brake lights of a towing package. You will want to check if they are installed and working properly. The next thing is to…
The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…
Hello Robert, Congrats on the new car! We do have a wiring harness that is available for pre-order the Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector - Preorder #C48RV. If you don't want to wait for that one to be released,…
Hey Teo, we have a solution for you but we don't have any harnesses that work as both a tow bar lighting kit and a trailer wiring kit. So what you'd want is the Curt part #C96JR for the tow bar lighting and then for the trailer wiring…
The Curt front hitch part #31199 is a fit for your 2WD 2004 Nissan Titan. If you check out the install picture I attached you will see that it does not extend out past the front bumper of a vehicle it is installed on.
Hello Dean, thanks for reaching out. We currently carry only the one transition plate, the etrailer Enclosed Trailer Transition Plate #e32JR. This is adjustable and has a maximum overall width of 82". it is made of steel. Sadly, we do not make…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Between those two color choices the black one would most likely be the ground wire. However, if you hook it up with the black as the ground and it does not work I would recommend trying the red wire. Also, you should trace both of these wires back on…
I have included a picture that shows the measurements needed for a spindle, bearings, seals, faces, and hubs. The spindle measurements are labeled A through F. A is the spindle shaft diameter B is where the grease seal sits C is where the inner…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Hey Colsen. I have some bad news for you. There are no hubs with bearings item #LM48548 and M12649 available. I checked elsewhere and there isn't a hub I can find anywhere that uses those bearings. The only solution I have for you is to replace…
You will first want to check the fuses on your tow vehicle. Some vehicles could have fuses for operating the turn signals and brake lights of a towing package. You will want to check if they are installed and working properly. The next thing is to…
The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…
Hello Robert, Congrats on the new car! We do have a wiring harness that is available for pre-order the Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector - Preorder #C48RV. If you don't want to wait for that one to be released,…
Heat guns are essential for electrical enthusiasts, perfect for tasks like installing trailer connectors or wiring projects. They offer precision and efficiency, making them a must-have for any DIYer looking to save time and achieve professional results.
Absolutely! A heat gun is perfect for installing trailer connectors, as it helps in securely sealing connections and ensuring durability. It's a time-saver for anyone working on a 2021 Chevy Colorado or similar vehicles.
A heat gun provides controlled heat, which is ideal for tasks like shrinking tubing or loosening adhesives. This precision helps in achieving clean, professional results quickly, making it a valuable tool for wiring both cars and trailers.
Look for adjustable temperature settings and a comfortable grip. These features ensure you can handle various tasks with ease and precision, whether you're working on a car or a camper trailer.
Always use the heat gun in a well-ventilated area and keep it away from flammable materials. Wearing protective gloves can prevent burns, ensuring a safe and efficient working environment.
Heat guns speed up processes like wire insulation and adhesive removal, allowing you to complete projects faster. This efficiency is especially beneficial when wiring both cars and camper trailers, reducing overall project time.
Filters
