Hey Don, thanks for reaching out! I recommend using the etrailer E-Track Backing Plates w/ Hardware #e66RR to secure the etrailer Horizontal E Track #e25VR to your hardwood floor. If you were going to be putting the bolts through the floor and into…
Hi Richard; we have no way of knowing what mounting bracket/brakes are on your Load Rite trailer. If you have Dexter/Tie Down Engineering disc brakes with a 9.6" rotor there is a good chance the #DX89UR will fit. However, it is probably best to…
Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…
The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…
The Aries Oval Nerf Bars #AA32ZD you're looking at are confirmed to fit your 2019 Ram 1500 Classic with the Quad Cab. This is the cab with the full front doors and the smaller rear doors. If you have the full doors at the front and the back then…
I attached a picture I got from Pace that covers exactly what the maintenance looks like for the Pace Switchblade tonneau covers like part #311-SWFA06A29 that you asked about.
Hey Jack, the Furrion Chill HE RV unit like the part #FR52PR is going to be your best solution. It is the quietest and draws the lowest amount of power at 11.2 amps compared to most similar options that are around 15. We've tested all of the…
The closest axle we have to what you need is the part #20440I-EZ-60 which has very similar specs as what you need, but the spring center is off by one inch as it is 48 inches on this axle. The overall capacity is 2,000 lbs and the hub face to hub…
To retain the skid plate of your 2020 Toyota Tundra TRD when installing the Draw Tite #65080 you will need to cut a 4 inch hole in the skid plate so you can access the oil filter. See attached picture.
The front mount trailer hitch options for a 2019 Toyota Tundra, the Curt Front Mount Trailer Hitch Receiver part #31198 or Draw-Tite Front Mount Trailer Hitch Receiver part #65080 will both work of TRD models. That said, you will either need to cut a…
Swapping tired hardware is simple with nylon bimini top parts that slide freely and fit well, even on older frames. For best results, match each piece to your tube size, flange thickness, and mounting hole spacing so everything stays secure.
Yes, expect nylon hardware with 1/4" flange thickness. If your current setup uses 3/16", plan to update matching pieces so everything shares the same flange size. Mixing sizes can cause strength or fit issues. Verify tube size and hardware style before switching.
They've held up well and performed as expected when matched to the right tube and hardware. Ensure the part fits the tube properly and tighten the screws firmly. If a replacement doesn't fit as tight as the original, it can come loose, so inspect periodically and retighten as needed.
Check for 1/4" mounting holes and 1-9/16" center-to-center spacing on the holes. Also verify an overall length of 2-1/2" and width of 7/8" if you're matching an existing mount. Measure your current hinge to confirm these dimensions before ordering.
They can, as long as the sizes match. Sliders and ends have fit on decades-old tops and often slide more freely than worn originals. If your old hardware was riveted, a screw-in replacement can hold, but confirm tube size and fastener style. Recheck tightness if the fit isn't as snug as the original.
Filters
