Can Clockwise and Counterclockwise Bauer Products T-Handle Be Keyed Alike

Question

Question:

Can I order 1 clockwise and 1 counter clockwise keyed the same ?

asked by: David C

0

Expert Reply:

Yes, since you can choose the handle based on the key it is possible to have the clockwise and counterclockwise Bauer Products T-Handle keyed alike. The # BA87VR and the # BA77VR both use the J-327 key so you can have matching locks on the handles.

expert reply by: Robin H

0

Answer 1

The Bauer Products T-Handle Lock for Truck Caps is offered in a few different configurations such as rotation direction (clockwise/counter-clockwise), finish (gloss black/matte black), and key number (127/327). Unfortunately, we don't offer the…

view full answer...

Answer 2

The Bauer Products T-Handle Lock for Truck Caps - Counterclockwise, #BA87VR and #BA84VR - Clockwise, each come keyed as a J-327 key so one key will fit each. I suggest you identify how the currently installed handles rotate as that is not something I…

view full answer...

Answer 3

Hi James; yes, if you order three of the Bauer Products T-Handle Lock for Truck Caps #BA59VR they will be keyed alike. They are all coded to the J-327 key number so they will all be the same.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Can Clockwise and Counterclockwise Bauer Products T-Handle Be Keyed Alike

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching