Replacement Vent Cover for 2003 Keystone Sprinter

Question

Question:

Vent covers of 14 X 14 they have a metal hinge that goes all the way across the back side and a metal piece that goes down the middle of the for the crank out the gaskets I'm looking for are for the vent they're all dry rotted I have three vents I need to be replaced seals gasket

asked by: Jacks4763

0

Expert Reply:

For your vent covers, there are four different hinge types that you might have. In order to know which replacement cover you need, the hinge style is very important. The sizes are all compatible, but the hinges are not. I've attached a photo to assist.

For your seals, I need to know the dimensions. If you are looking for grease seals for your hubs, I need a number printed on it or need you to measure it with digital calipers like # PTW80157.

expert reply by: Jason S

0

click to enlarge

Jacks4763

9/26/2017

Vent covers of 14 X 14 they have a metal hinge that goes all the way across the back side and a metal piece that goes down the middle of the for the crank out the gaskets I'm looking for are for the vent they're all dry rotted I have three vents I need to be replaced seals gasket

Reply

Jason S.

9/26/2017

For your vent lid, I recommend the Replacement Lid for Ventline and Elixir RV Roof Vents - Polypropylene - Smoke # CAM40148. This is also available in white # CAM40155. For the weather seal, you can use the Replacement Weather Seal for Ventline E-Z Lift Ventadome Trailer Roof Vents - 51" Long # BVE0127-00 or the Replacement Dome Seal for Ventline Ventadome Trailer Roof Vents # BVD0455-01.

Reply

Answer 1

For the wall surrounds, we have two options available. However neither has the exact dimensions you need. Better Bath RV Shower Surround - 40" Wide x 23-5/8" Deep x 57-3/4" Tall - White part #LC306207 Better Bath RV Shower Surround -…

view full answer...

Answer 2

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

Hey Dave, Looks like the BT-150 uses #L44649 bearings so you would be able to swap the hub out with the Easy Grease Trailer Idler Hub Assembly for 2K Axles #AKIHUB-545-2-G-EZ-2K. This comes with a #10-9 grease seal, which has a 1.5" inner…

view full answer...

Answer 5

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 6

I sure can! To replace the bearings in your 2023 Grand Design with Dexter 7,000 lbs axles you will need the following parts: Inner Bearing - Replacement Trailer Hub Bearing item #25580 Outer Bearing - Replacement Trailer Hub Bearing item #14125A…

view full answer...

Answer 7

The only difference between the Dexter 7K hubs and hub and drum assemblies that have either 1/2 inch studs or 9/16 inch studs are the studs themselves. Otherwise they are exactly the same. You can use calipers such as #PTW80157 to measure the…

view full answer...

Answer 8

The easiest way to determine what spindle your trailer has is to use a dial or digital caliper like the part #PTW80157 to measure it where the bearings and grease seal ride. I attached a picture that shows where these measurements are. If where the…

view full answer...

Replacement Vent Cover for 2003 Keystone Sprinter

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching