bing tracking image
  1. Trailer Lights
  2. Peterson
  3. Tail Lights
  4. Round
  5. LED Light
  6. Red
Peterson LumenX LED Trailer Tail Light - Weatherproof - Stop, Tail, Turn - 7 Diodes - Red Lens
etrailer Installation
We'll connect you with nearby partnered installers who know this exact setup.
Peterson

Peterson LumenX LED Trailer Tail Light - Weatherproof - Stop, Tail, Turn - 7 Diodes - Red Lens

Part Number: M826R-7
In Stock
$17.47
Retail:$28.90
You Save: 40%
Trailer Lights
zoom in icon
slider vertical icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.
By submitting this form, you understand and agree to our Terms of Sale, Website Terms of Use and Privacy Policy.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

Product Images

In Use/Installed

etrailer Installation
We'll connect you with nearby partnered installers who know this exact setup.
4-1/4" Round. LED trailer tail light serves 3 functions: brake, tail, and turn. LumenX optics creates a solid panel of light. Integrated voltage regulation. Recessed mount with grommet (sold separately). Accepts standard 3-prong plug. Great Prices for the best trailer lights from Peterson. Peterson LumenX LED Trailer Tail Light - Weatherproof - Stop, Tail, Turn - 7 Diodes - Red Lens part number M826R-7 can be ordered online at etrailer.com or call 1-800-940-8924 for expert service.
  • All Info
  • Reviews (108)
  • Q & A (0)
  • Videos (2)
  • Photos

Peterson Trailer Lights - M826R-7

Highlights

  • One Light, 3 Functions: Provides stop, tail, and turn signals in a single 4-1/4" round unit.
  • Brighter, Low-Power LEDs: 7-diode design gives strong light output with less power draw.
  • Consistent Performance: Integrated voltage regulation keeps brightness steady and prevents overheating.
  • Reliable In Wet Conditions: Skirted weld joint adds protection against moisture intrusion.
  • Easy Plug Connection: Uses industry-standard 3-prong PL-3 plug for simple wiring.
  • Road Legal: Meets DOT and FMVSS 108 lighting requirements for safe, compliant use.
Made in USA

Features to know about

Brighter, Low-Draw Lighting: 7-Diode LumenX LED Design

Older incandescent lights can fade or draw too much power, but this 4-1/4" round Peterson LumenX LED tail light uses seven white LEDs behind a red lens to create a bright, even panel of light. The integrated voltage regulation keeps output steady from 9V to 16V DC, so it stays consistent without overheating. At 12V it only draws 0.41 amps for stop/turn and just 0.01 amps for tail—plenty of visibility with very little power demand.

Reliable in Wet Conditions: Sealed and Skirted Weld Joint

Moisture can ruin lights fast, especially on trailers that see rain or road spray. This light’s skirted weld joint design adds extra protection against water intrusion, keeping the internal electronics safe. Because the LEDs are sealed inside the housing, there are no exposed bulbs or filaments to crack or corrode. It’s built for long-term reliability wherever you take it.

Easy Replacement Upgrade: Standard PL-3 Connection

Replacing an older Peterson incandescent light is simple with the standard three-prong PL-3 connector. It plugs right into existing wiring, so you can reuse what’s already there. The recessed mount fits in a grommet such as #426-18 (sold separately), making it a straightforward swap without wiring changes or custom brackets.

Close-up of Optronics PL-3 three-prong plug connection compatible with Peterson LumenX LED trailer light.

Long-Lasting Efficiency: No Bulbs to Replace

Frequent bulb changes become a thing of the past with this LED setup. The LumenX system lasts up to 50 times longer than traditional bulbs and uses far less power while producing a brighter, cleaner glow. That means more time on the road and less time chasing electrical problems or replacing fragile filaments.

Dependable, Compliant Performance: DOT and FMVSS 108 Approved

It’s not just bright—it’s fully compliant for use on the road. This light meets DOT and FMVSS 108 standards for automotive lighting and carries a 10-year limited warranty. You get dependable visibility that meets strict safety requirements and is built to last through years of use.

Specs

Dimensions

  • Overall length: 4-1/4"
  • Depth: 1-11/16"

Peterson LumenX 826R-7 round LED trailer tail light with red lens showing detailed dimensions for recessed mount installation.

Electrical

  • Diodes: 7
  • Power draw at 12V (Stop/Turn): 0.41 amps
  • Power draw at 12V (Tail): 0.01 amps
  • Input voltage: 9V - 16V DC

Warranty

  • Limited warranty: 10-Year

Recessed grommet mount trailer light installation diagram showing proper fit and positioning within trailer body.

M826R-7 Peterson LumenX LED Trailer Tail Light - Weatherproof - Stop, Tail, Turn - 7 Diodes - Round - Grommet Mount - Red Lens





Video of Peterson LumenX LED Trailer Tail Light - Weatherproof - Stop, Tail, Turn - 7 Diodes - Red Lens
Video Thumbnail Video Player Dialog

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.




Video Transcript for Peterson LumenX LED Trailer Tail Light Feature Review

Today we're going to be taking a look at, and showing you how to install the Peterson LED Trailer Tail Light. This light's going to give you your running light, your blinker, and your brake lights. What's great about these is that they're LED, which are really, really bright. So not only are they going to help keep you safe, they're also going to help other motorists on the road see you more clearly.The lights going to have seven diodes. What's really nice about the LED lights, you don't have to worry about any brittle filaments like you would with your traditional incandescent style lights. Not only are they going to last a lot longer, they're going to put off a more significant amount of light, and they're going to use way less power to do that.This light accepts an input of nine to 16 volts.

So this'll work great with your typical 12-volt system. The lights accept the industry standard three prong plug. If your trailer doesn't have one, you can find it on eTrader.com. In the back of the light, as you can see, we have our connection points, which do come covered dielectric grease. So that's one less thing you have to worry about during install.There actually is some raised lettering that tells you what each connection point will be used for.

I'll give you a couple measurements, and these will help you determine if this light will work with your application. It is four and a quarter inches wide, and an inch and three eighths from the end of the white to the end of the pod. I'll show you how easy it is to get these lights installed.They are designed to be used with a rubber grommet since we're replacing ours, we're just going to go ahead and put in a new grommet while we're doing that. If you need a new one, or a replacement, you can find one on etrailer.com. Now I'll show you just how easy it is to get this light installed.

Simply take our trailer wiring and feed it through the hole and just simply plug it in to the back of the light.Now sometimes these lights can be a really tight fit, so to help push it it, you can some silicone spray lubricant or just some soapy water, and that will make things a little easier. Just put it in and press, and you'll hear it pop into place. Now we can put some power to the light, make sure all the functions work. So here we have our tail lights, our turn signal, and finally, our brake lights. And if you purchased more than one light, you can repeat that same procedure for the other side.And that will do it for our look at, and installation of the Peterson LED trailer tail light..

Customer Satisfaction Score:

Ratings & Reviews

4.8

108 reviews
5 Stars
(88)
4 Stars
(15)
3 Stars
(4)
2 Stars
(1)
1 Star
(0)
Review Sort Icon
by:
Quickly answered my question and included links to what I needed to order. Got confirmation, shipped soon after, arrived today. Fits and works perfectly. Thank you!
by:
Works as expected. Made in USA
by:
Good price. Plug was a pain getting on but I finally got it.
by:
Peterson quality A+
by:
After a year of use, it's still in good shape and working well.
by:
Erickson always has very good products.
by:
by:
by:
by:
by:
by:
by:
by:
by:
by:
Exactly what I needed to fix my lighting problem.
by:
They fit and replaced the originals with no problem
by:
They look good but I have not installed them. My past experiences with your business have been good.
by:
looks good! Thanks for fast service.
by:
The lights were exactly as advertised, they fit in the existing holes perfectly and are so much brighter than the old ones
by:
Worked as advertised, a good replacement for my OEM lights.
by:
2024 Ford F-350 Super Duty
Customer service is the best! I had ordered with 2 day delivery but when I checked status it said part wouldn't be delivered until 5 days later. I live FT in a 5th wheel and as going to be gone from current location by then. They changed shipping to overnight and part arrived as needed, no add'l charge TY!.
by:
Nice light, but I believe that they should come with a gasket for wall mount scenarios.
by:
Easy instillation and very bright. But you must be very thorough that you have the right sized grommet for the hole in the bed or trailer AND for the light you are using. Not all grommets are the same as with trailers and flat beds so make sure that you double check the hole size both ways of the bed and the light to minimize head aches when you go to install.
by:
Fairly fast delivery. works as it should
25
108
true
Show More Reviews

See what our Experts say about this Peterson Trailer Lights

  • Replacement LED Trailer Light for Petersen 410-25 Light
    So what you have currently is our part # 435800 which we have a replacement LED style light for with the part # M826R-7. For an install grommet you'll then want the part # 426-18 and for a wiring harness part # 431-491 and you'd be set.
    view full answer...
    Image 1 for
  • Replacement Round LED Trailer Tail Light for a Peterson Round Tail Light
    The Peterson part number # 420-15 that you referenced is a replacement lens for the Peterson Round Trailer Tail Light # 431800 which has a 3-3/4" diameter. Although we don't have an exact match to this in LED we do have slightly larger sizes of round tail lights that come as LED. If you are wanting to go with one from Peterson then we have the LED Trailer Light # M826R-7 which has an overall diameter of 5-1/2" but the light diameter is only 4-1/4". The grommet # 426-18 and 3-prong plug...
    view full answer...
  • Replacing an Incandescent Peterson Light With a Peterson LED Light
    The Peterson LumenX LED Trailer Light # M826R-7 should replace your Peterson # 435800 without issue. That being said, though they are the same diameter, the grommet may not be able to be reused. I suggest also getting # 426-18 just to make sure you are covered. Both of these lights do use the standard 3 prong wiring design, so the wiring can be reused from your original setup.
    view full answer...

Do you have a question about this Trailer Light?


Info for this part was:

Employee Joshua S
Video by:
Joshua S
Employee Jacob T
Video Edited:
Jacob T
Employee Cole B
Installed by:
Cole B
Employee Ryan G
Installed by:
Ryan G
Employee Daron K
Edited by:
Daron K
Employee Brian T
Written by:
Brian T

At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.


Product Experts Available Now!
Call 1-800-940-8924