Replacing an Incandescent Peterson Light With a Peterson LED Light

Question

Question:

2005 Trailswest Horse Trailer Currently has your item #435800 I believe. Can I replace them with the LED M826R-7? Thank you.

asked by: Christine

0

Expert Reply:

The Peterson LumenX LED Trailer Light # M826R-7 should replace your Peterson # 435800 without issue. That being said, though they are the same diameter, the grommet may not be able to be reused. I suggest also getting # 426-18 just to make sure you are covered. Both of these lights do use the standard 3 prong wiring design, so the wiring can be reused from your original setup.

expert reply by: Lazer S

0

Answer 1

The Peterson LumenX LED Trailer Tail Light #M822R-7 does not include the wiring harness. They are sold separately. The correct wiring and plug for this light will be part #431-491.

view full answer...

Answer 2

The Replacement Lens part #A68RB that you referenced measures 3-1/2 inches long by 1-1/8 inches tall. If the lens you are looking to replace matches these dimensions then this would work for you. The part number for the light this lens is designed…

view full answer...

Answer 3

We don't offer a plug and play trailer harness that would plug directly into the Peterson #435800 trailer taillight. The lamp includes a 3 pin pigtail that would plug into the rear of the lamp which would wire directly into the trailer wiring. If…

view full answer...

Answer 4

I do have a solution, but the Peterson Thin Line #427400 doesn't have an LED equivalent. I could recommend a different light but that would require drilling new holes to get it mounted. What you can do instead is swap the bulbs to LED using the…

view full answer...

Answer 5

So what you have currently is our part #435800 which we have a replacement LED style light for with the part #M826R-7. For an install grommet you'll then want the part #426-18 and for a wiring harness part #431-491 and you'd be set.

view full answer...

Answer 6

The Optronics Trailer Light #STL43RB that you referenced can mount using rubber grommet #A45GB. But this light's overall diameter is 4-5/16-inches so this light unit would be too large to allow for grommet mounting in your trailer's…

view full answer...

Answer 7

The Light, Red Flush Mounted Sealed Turn Signal - Round #435800 will require holes that are 4-1/2 inches diameter for the grommet to fit properly. I measured this in our warehouse to confirm and have attached a photo to help.

view full answer...

Answer 8

We do have exactly what you need for tire chains that will allow you to traverse the snow, mud and ice, though the ones you asked about are not a fit for your size 37x13.5-17 tires. Instead, I highly recommend the Titan Chain Snow Tire Chains for…

view full answer...

Answer 9

Thank you for the pictures! We do not have an exact replacement but we have something extremely close. It is the LED Trailer Fender Light item #PE89BR. This light measures 3-7/8" long x 1-1/4" tall x 7/8" deep. It is a dual-face LED…

view full answer...

Answer 10

Although the DOT numbers you gave me are codes for what testing was done on the lights, I do have a solution for you. For your 2-1/2" round clearance light we have the Peterson Piranha LED Light #162R with the wiring and grommet as part…

view full answer...

Answer 11

The magnets on the Dexter Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4,400 lbs #K23-462-463-00 will be rated for 4,400 lbs. The magnets will have the same rating as the brake assembly. I am assuming you need magnets for…

view full answer...

Replacing an Incandescent Peterson Light With a Peterson LED Light

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching