Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This replacement inner member slide fits into the existing outer member housing of your Dexter DX7.5L and Legacy UFP surge brake actuator. For use with single-axle trailers with hydraulic disc brakes.
Features:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Jeff: Hello everybody, this is Jeff at etrailer.com. Today, we're going to take a look at this replacement inner slide for the Dexter DX 7.5L disc brake actuator for 2-inch hitch balls. It has a 7,500 pound weight capacity. Now this is the replacement inner slide that'll fit into your existing outer housing on your Dexter DX 7.5L or the legacy UFP disc brake actuator. Basically this inner slide is the portion that will telescope inside the outer housing of your surge brake actuator upon breaking, and it applies the force to the master cylinder to supply hydraulic pressure to apply the brakes on your trailer. If you notice on this one, it uses a nice low-profile coupler latch to ensure nice, easy, secure connection.
This is an over center latch mechanism, which will only engage when the actuator's fully seated on your 2-inch hitch ball. And I want to demonstrate that, I happen to pull a 2-inch hitch ball that this would fit onto.And just to show you how to install this, you pull out this tethered safety pin right here that allow you to open the latch. If you look on top of the latch, it has this round portion that goes back and forth. If you just push that over it'll release it, and that'll open up your latch, just like that. And with your latch open, you can see that when you're over the 2-inch ball, it'll fall right into place, put your latch back down, and now you're hooked onto the ball.
And then for extra safety, slide this safety pin all the way through, and that'll keep the latch locked onto the ball. If by chance this does get hit or something and it unleashes it or unlatches it, that latch won't open all the way it'll still stay attached to the ball, and then you just push it back down.And then to totally remove it, just slide your safety pin back out, slide open your latch, and that'll open all the way, and you can remove it from the ball just like that. So it's a very simple way to connect and disconnect from your hitch ball. Also, if you notice it has this breakaway cable, which is included. Now this breakaway cable is required by law, this will attach to your tow vehicle.
And what this does is when it's attached, it will prevent a trailer runaway situation. So if this trailer happened to become detached from your tow vehicle, it would pull on this breakaway cable, which would then activate the master cylinder to apply the brakes on the trailer to prevent a runaway situation. Now, the master cylinder itself, let me flip this over and you'll be able to see it. Right here, this master cylinder is a constructed of aluminum rather than plastic or steel. It gives you a nice increased strength and corrosion resistance.And if you notice on the back of the master cylinder right here, you'll see it has the Selectric reverse lockout solenoid.
This will let you back up without actuating your trailer brakes. The solenoid, you can see the wires here is wired to your reverse light circuit, and it activates automatically when you shift into reverse. Again, the application on this is single axle trailers with disc brakes. The ball size we mentioned it fits on is a two inch diameter hitch ball. Weight capacity is 7,500 pounds. But that should do it for the review on this replacement inner slide for the Dexter DX 7.5L disc brake actuator, for 2-inch hitch balls. It has a 7,500 pound weight capacity..
Customer Satisfaction Score:
95% were satisfied with this product
5% of customers were not satisfied
Ratings & Reviews

Chris W.
9/1/2025
After a year of use and sitting in the Florida heat, humidity, and sun there have been no failures to be noted. Electrical wiring was wrappedplaced in split loom for protection and is still in good working order.

Wendell
5/16/2023
A year with several long road trips 300+ miles and dozens of local trips and the actuator is still working like new.The only change Id like to see is the ability to use a more robust locking pin to secure the trailer. The small diameter pins that will fit through the coupler bend easily.

Thomas
10/20/2023
Working as it should. No leaks. Boat brakes still working.

John S.
3/13/2023
The Dexter brake accuator is still doing what its supposed to. Installation was somewhat simple after removing some rusty parts from the original. New unit installed easily and works great after a good bleeding of the lines.

Scott
2/7/2023
Product is on point and working as expected. I should have made this purchase previously before trying to do piece meal. Easy to install and much easier..

Sierra K.
11/9/2021
Customer Service will contact you about the damaged item. This is our only inner member we have for a single axle wdisc actuator.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.






Paul
7/12/2026
Fantastic product. Everything still works exactly as it should.