Why Does Reverse Lockout Solenoid of Replacement Inner Member for Dexter DX7.5L

Question

Question:

What are the 2 wires for on the the solenoid? My current A-60 only has the 1 blue wire for the reverse lockout

asked by: Bryan C

1

Helpful Expert Reply:

Some reverse lockout solenoids have one wire as they ground through the coupler to the frame whereas some have a separate ground wire like with the Replacement Inner Member for Dexter DX7.5L part # DX39FR. The blue wire would get ran to the reverse circuit and white wire gets ran to the ground.

expert reply by: Jameson C

1

Answer 1

The #DX39FR Replacement Inner Member for Dexter DX7.5L Actuator - Single Axle w/ Disc - 2" Ball is what you need. This is the replacement inner member for Dexter DX7.5L and Legacy UFP Brake Actuators like your UFP A-60 so it would be exactly the…

view full answer...

Answer 2

Hey Reid, You can do exactly what you were wanting to replace the inner member of your A-60, and since you have a single-axle trailer you do indeed have the right part: - Replacement Inner Member for Dexter DX7.5L Actuator - Single Axle w/ Disc -…

view full answer...

Answer 3

Thanks for the picture and your patience! I did some research and made some phone calls, the correct replacement for your actuator is the Replacement Inner Member for Dexter DX7.5L Actuator - Single Axle w/ Disc - 2" Ball - 7,500 lbs item…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

We do have the Replacement Master Cylinder Assembly #DX44FR or Inner Member #DX99FR (tandem axle)/ Inner Member #DX39FR (single axle) for your Dexter A-75 master cylinder. If the master cylinder is the only damaged part that is all you will need to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Why Does Reverse Lockout Solenoid of Replacement Inner Member for Dexter DX7.5L

Product Page this Question was Asked From

Continue Researching