Do You Carry Just the Inner Portion Of The Dexter DX7.5L A-60 Brake Actuator For Disc Brakes?

Question

Question:

Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Weld On - Disc - 2 Ball - Primed - 7.5K can you buy without cover all i need is the slide in portion not the weld on out side

asked by: Charles S

0

Expert Reply:

We do have the Replacement Inner Member for Dexter DX7.5L Actuators and Disc brakes. You would need to select the Single Axle # DX39FR or Tandem Axle # DX99FR version.

expert reply by: Bud M

0

Answer 1

The main difference between The Dexter Inner Membrane #DX99FR and The Dexter inner Membrane #DX39FR is that the #DX99FR is for a tandem axle with disc brake setup. The #DX39FR is for a single axle with disc brake setup. Both Dexter membranes have a 2…

view full answer...

Answer 2

I would be happy to! Other then what you pointed out, the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout item #DX63FR fits a 3" x 3" or 3" x 4" straight tongue. The Dexter item #DX93FR fits a 3" x 5" straight…

view full answer...

Answer 3

Yes, the replacement inner member part #DX99FR does fit your UFP A-60 actuator and will work perfectly fine with the tandem axle disc brake setup you have now.

view full answer...

Answer 4

We have the inner member for the Dexter Brake Actuator part #DX56FR with the #DX99FR which is what you are looking for. This is a 7,500 lb rated disc brake inner member that is compatible with tandem axle setups.

view full answer...

Answer 5

We do have a potential solution for you. Unfortunately, the swing away actuators like the one on your 2005 Mastercraft trailer have been discontinued, so I am afraid there is no direct replacement, or anything that will fit inside the current swing…

view full answer...

Answer 6

Yes, you could remove the inner member of the Dexter DX7.5L A-60 to replace the bad member of your UFP A-60. Our pricing algorithm can be a little confusing so if this is the less expensive route than just the inner member part #DX99FR it is what I…

view full answer...

Answer 7

We do carry the Replacement Inner Member #DX99FR that fit the Dexter DX7.5L A-60 Brake Actuator #DX56FR and Legacy UFP brake actuators. This would allow you to replace just the inner portion of your current actuator as long as yours is one of the…

view full answer...

Answer 8

If you have a coupler actuator that looks like the #DX29FR but it mounts inside the channel on the trailer frame what you would most likely actually want is the inner member of this coupler with the part #DX99FR. This is the inner section of the…

view full answer...

Answer 9

The pins on the Dexter DX7.5L A-60 Brake Actuator #DX63FR are removed by releasing the snap rings and washers from one side of the actuator. You will then be able to press out the pins. Do note depending on the age of your actuator and the amount of…

view full answer...

Answer 10

The Replacement Shock Absorber Spring Kit #TK71-758-00 is the correct shock for your UFP Surge Brake Actuator. The picture you included does not specify if it is for a disc or drum brake set, so I have found both for you to choose from. Disc Brake…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Do You Carry Just the Inner Portion Of The Dexter DX7.5L A-60 Brake Actuator For Disc Brakes?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching