Replacement Step, Motor, and Control for Kwikee RV Electric Steps - Platinum Series

Kwikee RV Steps - LC372558

Replaces the electric steps, motor, and control unit for your Kwikee Platinum series RV step. Motor and control unit automatically extend and retract the steps when you open and close the door. Wiring pigtail hardwires to your RV's power.

Features:

• Replaces the steps, motor, and control unit for your Kwikee Platinum series steps
  • Switch kit (LC369311) for extension override sold separately
• Motor works with gearbox to extend and retract the steps
• Control unit wires steps and step light to the opening and closing of the RV door
• Amber incandescent light illuminates steps to make them easy to see at night
• Integrated safety features help prevent damage to the steps
  • Motor retracts the steps if they strike an obstacle during extension
  • Ignition override retracts the steps when the vehicle's engine is started
• Non-slip tread and easy-to-see reflective strips on step surface
• Sturdy, powder coated steel construction with weatherproof wiring withstands the elements
  • Solid steel drive rods and stainless steel bushings provide additional durability
  • Air pressed rivets at pivot points ensure long-term strength
• Simple installation with existing mounting holes
  • Switch Pack (905325000) and 4-way wiring harness (301692) sold separately
  • Hardware not included
• Made in the USA

Specs:

• Extended height: 16-7/8"
  • Folded height: 10-3/4"
• Overall width: 25-3/4"
• Mounting plate dimensions: 23-3/4" wide x 11-3/8" deep
• Bolt pattern: 22" wide x 8" deep
• Step dimensions: 24" wide x 11-1/8" deep
• Drop/Rise: 9"
• Voltage:
  • Motor: 12V
• Control unit amperage: 10A
• Light bulb type: C193, incandescent
• Control unit wire gauge:
  • Green: 12 AWG
  • Purple: 16 AWG
• Weight capacity: 300 lbs
• 1-Year warranty

Note: This step assembly includes the steps, motor, and control unit only. The steps will operate automatically, extending when the RV door opens and retracting when the door closes.

If you want the complete step assembly that also allows you to override the automatic retraction so the steps stay out whether the door is open or closed, you will need a switch kit (sold separately).

The 4-way plug (sold separately) fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail can help you hardwire the unit to your RV.

Safety Features

The Kwikee steps include several safety features in an effort to prevent injury to you or your passengers and damage to the RV steps. If an obstruction is detected while extending, the steps will halt and retract back into the stowed position. The steps will also retract when you turn on the vehicles ignition, even if the automatic retraction override has been activated, in case you forget to stow them before driving away.

Will Kwikee Electric Steps Work for You?

Electric steps are typically installed on RVs and some travel trailers. The electric steps from Kwikee install and fold up underneath the camper for simple storage. To ensure you choose the correct size for your application, there are a few measurements you will need to take.

The Kwikee electric steps attach to the underside of the camper chassis, directly beneath the doorway. To decide which size you'll need, locate the space available underneath your camper that lines up with the doorframe, and measure the width and depth. You will need a mounting space that is at least 25-3/4" wide and 11-3/8" deep.

If it turns out you have more or less space beneath your doorway, there are other step assemblies available with bracket sizes ranging from 24-3/4" wide to 37-1/4" wide. A full list of the available steps is below.

Outriggers - metal brackets that act as an extension (LC301704 - sold separately) - may be needed for installation depending on the model of your original stairs. These provide extra length if the old steps are longer or wider than the new.

Once you know where the mounting bracket will go and what size mounting bracket you need, that spot will be used as the "mounting point" to determine how many steps you will need.

How Many Steps Do You Need?

To decide on how many steps you'll need, measure from the mounting point to the ground. This is called the entry height. The entry height should roughly match the height of the steps when they're fully extended, plus 6" to 8" to account for the drop from the bottom step to the ground. This measurement will also tell you how many steps you need.

The chart below displays mounting bracket widths in the first column and entry height measurements in the second column. The third column shows the corresponding part numbers. Use the mounting bracket width and entry height measurements you took to determine which part number will fit your RV. Choose the bracket size that is closest to your measurements without going over.

This page's step assembly is in bold text.

*Motor and control unit

**Motor and switch kit

***Motor only

How Do You Install the Steps?

To install the steps:

1. Hook up the steps to power to verify that all components are in working order
2. Make sure the camper is level on flat ground
3. Lift the steps into the mounting space and prop into place
4. If needed, mark the mounting holes on the camper and drill

   -Set aside steps before drilling

5. If needed, install the outriggers
6. Align step mounting holes and secure in place with carriage bots and flange lock nuts

   -Make sure bracket is backed up fully against the I-beam on the chassis

   -Hardware not included

7. Tighten hardware until snug
8. Make sure assembly is sitting square and level
9. Torque the hardware tight
10. Connect the appropriate writing to your vehicle's source

372558 Lippert Components (LCI) Quickie Platinum Series Motorized Motorhome Entry Steps - 2 Stairs - 9" Drop/Rise - 24" Wide - 300 lbs

Kwikee Part Number 9010000220