Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
The motor and control unit on this Kwikee Revolution step extend and retract the 22-7/8" wide x 8" deep step automatically when the door opens or closes. It runs on 12V power and draws 10 amps through the control unit, so it moves smoothly without jerking. With a 5-1/2" drop/rise, the step feels natural underfoot instead of steep or awkward.
You don’t have to worry about the step being left out or hitting obstacles. The ignition override pulls the step in when the engine starts, and the motor retracts automatically if it meets resistance while extending. These safeguards protect the step and keep you from driving away with it deployed.
The frame is made from sturdy, powder-coated steel with solid steel drive rods and stainless steel bushings at each pivot point. Air-pressed rivets add extra strength, and the sealed wiring is weatherproof to handle rain and road grime. With a 300 lb capacity, it stays steady and resists flexing even with heavy use.
Each step surface has a non-slip tread and reflective strips that help you see the edge clearly. An amber incandescent C193 light illuminates the step when extended, making nighttime entry safer for everyone.
This assembly replaces the step, motor, and control unit for Kwikee Revolution models using a 25-5/8" wide x 11-1/8" deep mounting plate and a 24-5/8" x 8-3/4" bolt pattern. It connects with the included 4-way plug or hardwires using the supplied pigtail, making it a straightforward replacement for worn or damaged units.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today you're going to be taking a look at the lifter components quickie 36 series single electric step. Stepping up into your RV can be a bit of a challenge. Especially if the steps aren't working. That's where our replacement steps are going to come into play. With our step installed, when we open the door it's going to automatically come out allowing us to step in easier getting in our RV but at the same time when we close the door, they're going to automatically retract making sure they're not going to catch on anything when we're driving down the road.Now from the top where it's mounted behind this panel, our step is going to drop down a total of five inches. In our application and the step we're using is going to be 24 inches wide by 10 and three quarter inches deep.
There is another step that is available that's going to be 30 inches. To see our website for your specific application and it's going to be made of a nice solid steel construction and have a nice black powdered finish for long lasting durability.The hidden amber light underneath our step is going to make it a lot easier for us to find that step in low light situations and have confidence when we're getting in or out of our RV. The included motor on our step is going to have a solid steel drive rod as well as stainless steel bushes for extended life of the motor. Our steps come with a door switch allowing it to know when to open up and when to close.Now our step is also going to come with a rocker switch in case you choose to manually turn it on and off and not use that door switch. Now that we've seen our steps and gone over some of the features, we do realize that every RV is going to be slightly different but we'll go ahead and give you a brief overview of how to get them in place.To begin our installation, you're going to need to remove your steps and disconnect al the electrical components that are on the steps themselves.
So I got our new step here and we're going to have our pigtail that we're going to wire into our motor home. Then the pigtail is coming off the step as well as the ground wire.So to get our step extended to make it a little easier to work with, I'm going to go ahead and plug in our pigtail and then I have a jump box here which is going to provide my power and grout. So I'm going to take the green wire with the ring terminal on it. I'm going to hook it to ground. I'm going to take my red wire, hook it to power, and then now we're going to take our jump box and turn it on and that should extend the step out.
We've made it a little bit easier to get access to our mounting holes.It's a good idea to have something underneath the step to support it. I'm using a floor jack to help me get the new step in place. It takes a little bit of patience to get everything lined up because it is rather hard to see but once we get the holes lined up, we can put our hardware in hand tight so that step will support itself and we can come back and tighten it all down.Typically you're going to have four bolts, one on each corner holding your step in place. There may be more but you just want to make sure that you replace them all and get them all nice and tight. Now these are the wires that we cut and as you can see they have some inaudible 00:03:15 connectors on them.
That's because it was hardwired into the motor. Now we're going to use the other end of the pigtail and then just connect our wires here so we can have a quick disconnect and if any issues arise we can disconnect it. It would be a little bit easier rather than cutting and splicing every time.So we'll go ahead and cut back these butt connectors and strip the wires and start attaching everything color for color. We're going to take a heat shrink butt connector and now these don't come with our kit but if you need some you can pick some up on our website. Then we can take the other end of our pigtail and we'll find the brown wire. It's already prestrippe.d So we can just put it into the other end of our butt connector and crimp it in place. Now we're going to do that for each one of our wires and we're going to connect them color for color. You should have a white, a yellow, and a red left on the motor home end as well as the pigtail end.We'll be using a heat gun to shrink down the connectors. I just want to mention if you are using an open flame you want to be extra careful not to burn the wires or the connectors themselves. Now this is where our ground from our previous step was installed. I'm going to go ahead and remove that bolt, take our new ground wire, slide the bolt and washer around it, and line up the hole and reinstall that bolt. With the jack out of the way, we can go ahead and shut our door. We can go ahead and go back underneath and start cleaning up all those wires.That'll finish up your look of the lifter components quickie 36 series single electric step.
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
Ratings & Reviews
Right part delivered in good condition and exactly on the schedule they projected. Much appreciated.
The Lippert Kwikee Revolution steps that I purchased replaced the same steps that had failed on our Winnebago Coach after five years of service. I would give the steps 5 stars except that I had to match drill the new steps to the existing mounting studs under the coach as they were fractionally different which did not allow the step frame to mount to the coach. Otherwise, the instructions were clear and concise and the steps activated perfectly when electrically connected. Kudos to Anna at etrailer for her capable and friendly assistance in completing the sale.
etrailer had the exact replacement for my 10year old Kwikee RV steps. They fit and worked perfectly since I replaced them. etrailer is my go-to place for RV parts.
Stairs are installed and working well. Great customer service and follow up!!!
Identical replacement, works well in my 2012 Winnebago Via 25R. Easy one-man installation (with a jack to secure the old one coming out and the new one going in).
Easy replacement. Works fine.
Amazingly, easy to put on. Excellent quality of material.
Easy install. Works perfectly.
Fast shipping, great replacement for the Winnebago EKKO motorized steps.
Perfect fit and works wonderfully! Thanks Sara R!
This Revolution Midi Miki 2 step matched exactly what I replaced. I used a car jack and a piece of 4x4 scrap to hold it in place. My wife helped with the jack, allowing me to use both hands for positioning. Not a hard replacement WITH A GOOD HELPER. Customer service was very good. They nailed what I needed. Thanks.
The step arrived in a timely manner. However the step was not quite the right fit. It is lighter than the one we had on it and it was narrower. My husband was able to make it work, but it is not a perfect fit. I ordered what was supposed to be the replacement for our step system.
Exact replacement for our unit.
From the time I ordered to the moment I received the item reps were communicating with me along the way, informed me of any delays, even suggesting alternative so I can have it sooner. Customer service like this is hard to find these days.
Item arrived as promised and is already installed. Works great!
Thank you
This product was a perfect fit, simple plug and play kind of thing and fit right into my rig.Fred and the gang at etrailer were great. They offered to take this thing back and pay for shipping if it wasn’t the right one or didn’t fit. I will use these folks again. Shipping the product took no time to get here. Thanks again etrailer.
exact fit!!
Product was as described and received in great condition.
I am happy to hear from you and your team. I was impressed with all the help to help me get the right step. Thank you!
It functions perfectly and was everything it was said to be! Thank you!
Easy to install, fast shipping, no problems or issues to report, step works like it is supposed to.
Easy to contact, came in on time, installed and working fine.
George i contacted e trailer reference no paperwork arrived with unit. E trailer states warranty is 90 days. I contacted Leipert they said 1 year warranty . I requested paper work for documentation already in process Thanks Again
The step fit perfectly! I replaced the old step in less than 1/2 hr
Step Unit quit working 5weeks - when the customer associate was contacted each (at first spoke with 3 tech associates total) each had many questions for me to answer along with me providing pictures of product, labels and later for me to removed motor part. Next for them to authorize exact part replacement (for me to repair). After all the efforts answering technical questions taking voltage samples hooking up external 12vdc power supply to verify for the associates that motor unit operation (still didn’t work). I Was re-roughed to a parts associate who asked again same questions and provided pics sent previously for tech associates making sure everyone had same information. New step motor was shipped and received wrong part doesn’t even fit nor even work on the step model information I provided to all the associates. I requested a correct part be shipped and have been assured correct part will be sent. Now Over two months later I have not received replacement part. Email was noted an overnight shipment would be arranged- I replied verifying request to ship new part. No part has been provided nor any shipment notification for part was on its way. Todays date my now disassembled step is not operational and no help getting past this new step purchase failure.
Any help would be greatly appreciated!
Do you have a question about this RV Step?
Condition: Surface Scratches
Notes: Item has cosmetic scratches.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Katrina B.
10/3/2022
I am sorry to hear that you are having this issue. This item does have a one year limited warranty. I have sent your information over to our customer service department for them to get in touch with you about a possible warranty.