Replacement Frame For Kwikee Step 372558

Question

Question:

I have LCI 372558 step. I would like to get frame only. Is this possible and how much would it be?

asked by: Bill

1

Helpful Expert Reply:

Yes, we have the frame only for the Kwikee Step # LC372558; the correct part is as follows:

- Replacement Step Frame # KW54FR

All prices can be found either on the product page or just by scrolling down.

expert reply by: Kyle S

1

Answer 1

The picture came across pretty blurry, but I was able to pull enough off of it to determine that you have the Kwikee RV Electric Steps - Platinum Series #LC372558. The correct replacement motor for those steps is the Replacement Motor for Kwikee…

view full answer...

Answer 2

It sounds like you are going to need either the Replacement Motor for Kwikee Electric RV Steps part #LC379147 or the Replacement Gear Box and A Linkage part #LC379160. I spoke with Lippert and was able to cross reference the info provided so I can…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

That’s a great question Chadwick, and this is one of those situations where the change in technology really matters. The GE Appliances Low-Profile RV AC w/ Heat Pump part #GE26RR will replace your current ARC13AACBL2 setup, but it’s important to know…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey John! You weren't finding that SolidStep because Lippert discontinued it in 2024 and that table wasn't updated to reflect this. What I recommend instead is the MORryde StepAbove RV Steps #MR26RR. These are designed to fit 23-3/4" to…

view full answer...

Answer 11

Appreciate you reaching out Juan! Lippert confirmed that your LCI number is a 1621 pin box. Rota-Flex 5th Wheel Pin Box #LC328330 is going to be a direct replacement and bolts right on. The Rota-Flex pin box is highly rated because it has a pivoting…

view full answer...

Answer 12

The Kwikee Control Box #909506000 has been discontinued by the manufacturer. The replacement part is determined by the date of manufacture which you can determine by looking at the current part which will have a date on it. If not, you can supply the…

view full answer...

Replacement Frame For Kwikee Step 372558

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching