See what our Experts say about this Lippert Accessories and Parts

• Where are Circuit Breakers/Fuses Installed on Lippert Electric Stabilizer Jacks
  The Lippert stabilizer jacks like you have use an 6 amp auto reset circuit breaker and a 20 amp fuse or breaker. If you check out the diagram I attached you'll see how it normally would be wired. For a 20 amp breaker you'd need the part # PK54520 and for a 6 amp breaker part # LC134181. If somehow the motors are bad they are part number # LC138445.
  view full answer...
  
• Replacement Parts for Lippert Electric Stabilizer Jack
  There are not replacement legs available for the Lippert Components High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift # LC369774 which is the same as the 198641 you mentioned. You will need to replace the entire unit. The support arm # LC1134122 in yellow or # LC1134121 in black is the only non-electric component able to be separately replaced. The motor # LC138445, circuit breaker # LC134181, and switches # LC144214 or # LC387874 as well as switch housing # LC134025 are...
  view full answer...
• Fuse and Breaker Locations on Lippert Power Stabilizer Jack for Forest River Trailer
  On the Lippert Power Stabilizer Jack # LC298707 for your Forest River Evo Trailer Trailer there should be a 20 amp (or higher) fuse/breaker located inline with the red power wire coming from the switch before it reaches the battery. Check to make sure the fuse is in good condition and replace if needed. You can also check the 6 amp auto reset breaker that is located inline with the red wire from the switch that goes to the jack's motor. If you find it needs to be replaced you can use...
  view full answer...
  
• Troubleshooting Lippert Electric Stabilizer Jack Not Working
  We have actually heard from Lippert about this type of issue and they recommend replacing the 6 amp fuse with a 30 amp fuse. This should resolve the issues you're describing.
  view full answer...
  
• Wiring Diagram for the Replacement Electric Jack Switch with Harness # LC387874
  Yes, I have attached the wiring diagram of the Replacement Electric Jack Switch with Harness # LC387874 for you to reference. Basically the Blue wire goes to a 6A auto reset breaker, like part # LC134181, which then goes to the positive circuit for extending, the Yellow goes to the positive circuit when retracting, the Red wire goes to the positive battery terminal, and the Black wire goes to the negative battery terminal.
  view full answer...
  
• Can You Check Lippert Auto Reset Breaker
  Hey Jack, welcome back! You can use a multimeter like # PT89ZR to check a breaker like the # LC134181. Set it to DC and make sure you're getting 12V on both terminals. If not, go ahead and replace it. Did you ever sort out the problem with your Curt Echo?
  view full answer...
• Can Replacement Lippert Components Power Stabilizer Jack LC298707 Be Installed Using Current Wiring
  Since the Lippert Components Power Stabilizer Jack # LC298707 is a direct replacement for your 337199 Lippert Jack it will be compatible with your current wiring. This comes with a new switch and breaker part # LC387874 for the switch and part # LC134181 for the 6 amp Auto Breaker.
  view full answer...
• My Rear Camper Jacks Are No Longer Working, Checked Fuses, What Could Be The Issue?
  Hey Stacey, If you have already checked the fuses and wiring and nothing seems to be blown or damaged it could be an issue with the circuits. You will want to take a circuit tester and check the voltage across the circuits. Check if there is power going to the motor, if there is and they are not working the motor is bad. Check at the switch as well, if there is power to the switch then the switch is bad. If there is no power at the switch check the circuit breakers and voltage there....
  view full answer...
• What Replacement Parts Are there for the Lippert 337199 Stabilizer Jack?
  Hi Jim, The Replacement Electric Stabilizer Jack Support Arm for Lippert RV Jack - Yellow Part # LC1134122 you were looking at are a confirmed fit for the Lippert 337199 stabilizer jack. However, the Lippert 337199 is an obsolete model of the PSX1 26-inch electric high-speed rear power stabilizer jack for RVs and trailers. It has been discontinued, which is why we're limited in replacement parts. I'm not sure what part you're specifically needing to replace, but we do have a few other...
  view full answer...
• Replacement 6-Amp Auto Reset Breaker for Lippert Electric Jack
  The Replacement 6-Amp Auto Reset Breaker for Lippert Components Power Stabilizer Jack # LC134181 are designed for use with the Lippert Electric Stabilizer Jacks that have switches such as the Lippert Components High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit # LC298707. I would not be able to guarantee any other breaker will work with this jack. If the Lippert jack is what you have, then the reset breaker is exactly what you need; to order one to your home in Canada you...
  view full answer...
• How to Install the Replacement Electric Jack Switch with Harness # LC387874
  I have attached a diagram that demonstrates how the typical wiring will need to be installed for the Replacement Electric Jack Switch with Harness # LC387874 that you referenced. Black Wire - Ground Battery Red Wire - Power Battery (20A Auto Reset Breaker # PK54520 will need to be installed in-line) Yellow Wire (Retract) - Black Motor Wire Blue Wire (Extend) - Red Motor Wire (6A Auto Reset Breaker # LC134181 will also need to be installed here)
  view full answer...
  
• Troubleshooting Lippert PSX2 Legs Won't Extend or Retract
  There is a fuse/breaker on the red wire between the switch and the battery. If it is bad you can replace it with # LC134181. When you say traced did you mean you tested for 12V power? If not, go ahead and test it with a circuit tester # PTW2993. More than likely you aren't getting full 12V power, or none at all. If you have 12V power running to the switch check the wire running to the motor for power. If you find that you have 12V power running from the switch to the motor but nothing...
  view full answer...
• How to Wire Lippert Replacement Electric Jack Switch # LC387874
  There will be 4 wires coming from the Lippert Replacement Electric Jack Switch # LC387874 that you are looking at. The blue wire from the switch will go to a 6 amp breaker like # LC134181 that is installed between the switch and jack motor. This will go to the positive circuit on the jack when it is extending. The yellow wire will go to positive circuit when retracting. The red wire will go to the positive battery terminal and the black wire will go to the negative terminal for ground....
  view full answer...
  
• Can The Auto Reset Breaker for Lippert Power Stabilizer Jacks Be Reset?
  The 6-Amp Auto Reset Breaker for Lippert Power Stabilizer Jack # LC134181 is self-resetting. It automatically will reset itself after the breaker trips. If the circuit continues to draw more amperage than the breaker is rated for it will constantly trip and reset. You will be able to hear this if you are close to the breaker as it is happening. While it is possible for the breaker to go bad, since your jacks are going up fine it sounds like your motor may be overloading or the switch is...
  view full answer...
• Replacement Parts Available and Hardware Included With Lippert High-Speed Stabilizer Jack # LC369774
  The Lippert High-Speed Power Stabilizer Jack # LC369774 includes the following parts. 1- Stabilizer Jack Assembly 1- White Switch Housing # LC134025 1- Power Switch # LC144214 1- 6 Amp Auto Reset Breaker # LC134181 4- 3/8" Hex Head Mounting Bolts 4- 3/8" Hex Nuts The following replacement parts are also available for the Stabilizer Jack Assembly - Replacement Electric Stabilizer Jack Support Arm # LC1134122 - Replacement Electric RV Stabilizer Jack Motor # LC352338 - Replacement Foot...
  view full answer...
• Replacement Switch for a Lippert PSX2 Electric Stabilizer
  It could be the motor. If it sounds the same and you're not hearing any grinding or gear noise then the motor should be good. You'll also want to check all your wiring to see if there's a lose ground or a connection that's coming lose. You can replace the switch on your Lippert PSX2 Electric Stabilizer with the Replacement Electric Jack Waterproof Switch with Harness for Lippert High Speed Stabilizer Jacks item # LC387874.
  view full answer...
• Troubleshooting Circuit Breaker of Lippert Stabilizer Jack that is Tripping
  It's not out of the question that the breaker could be bad which we offer the part # LC134181 as a replacement but it's also possible it's something else like the motor being bad and wanting to draw too much amperage which is causing it to trip. We have the replacement motor with the part # LC138445. You could bypass the breaker and see if the motor runs and if the wire starts to get too warm. If it works fine it's the breaker but if the wire starts to get warm it's the motor.
  view full answer...
• Troubleshooting Electric Stabilizer Jacks Suddenly Not Working on Trailer
  The fact that the electric stabilizers on your Forest River Super V Trailer failed at the same time leads me to believe that the issue is at the power source. It's very possible that the battery has enough juice to send power to the motors but not enough to actually operate the jacks when under load. This actually isn't terribly uncommon. I highly recommend inspecting your battery to make sure it's fully charged and in good condition. Also check that the power wires are securely attached...
  view full answer...
• Testing Circuit Breaker for Lippert Stabilizer Jacks
  Probe the wire before and after the breaker with a circuit tester like part # PTW2993 to see if there is power on one side of it but not on the other. That's the easiest way to test it.
  view full answer...
• Troubleshooting Lippert Stabilizer Jack No Longer Working
  I really sorry to hear about the trouble you're having with the rear Lippert Stabilizer Jack # LC298707 on your travel trailer. The sporadic operation you're experiencing makes me think there's either an issue with the power source/connection or with a weak ground. The first thing I recommend doing is tracing the power wire all the way to the battery, making sure there aren't any pinched, exposed, or otherwise damaged portions of wire that need to be repaired/replaced. Verify that the...
  view full answer...
• Lippert PSX1 RV Stabilizer Motors Not Working When Installed on RV
  I spoke with the folks at Lippert who tell me that your issue sounds like a ground problem. The fact that you can get the motors to operate independently of the coach by directly attaching them to a battery would tend to confirm a poor ground connection. I've provided a wiring diagram for the Lippert PSX1 stabilizer.
  view full answer...
  
• Installing Replacement Electric Jack Switch for Lippert High Speed Stabilizer Jacks
  The Electric Jack Switch with Harness for Lippert Stabilizer Jacks # LC387874 referenced in your question will have 4 wires coming from the unit. The blue wire from the switch will go to a 6 Amp Auto Reset Breaker # LC134181 that will be installed between the switch and the jack motor. The yellow wire will be connected to the black wire coming from the stabilizer jack. The red wire will go to the positive battery terminal and the black wire will go to the negative terminal for ground....
  view full answer...
  
• Where Are The Fuses And Circuit Breakers Located On A Lippert Electric Stabilizer
  The Lippert Stabilizer uses a 6 amp auto reset circuit breaker and a 20 amp fuse or breaker. If you look at the diagram below you'll see where they normally would be located at. For a replacement 20 amp breaker # PK54520 will work and if you need a 6 amp breaker # LC134181 is the correct one. The switch # LC387874 could also be bad and need replaced.
  view full answer...
  
• Replacement Relay for Lippert Stabilizer Jacks on RV
  Sounds like you are looking for a replacement breaker for your Lippert stabilizer jacks # LC369774 which we have with the part # LC134181.
  view full answer...

Do you have a question about this Accessories and Part?