Menu Icon
Pin and Clip For Class I and II Trailer Hitch Receiver Hitch

Pin and Clip For Class I and II Trailer Hitch Receiver Hitch

Item # PC2

lowest price pledge

Our Price: $7.25

Hitch Pins and Clips

Orders above $99 qualify for Free Shipping

Shipping Weight: 0.47 lbs

Quantity: 
In Stock, Ships Today
Pin and Clip For Class I and II Trailer Hitch Receiver Hitch
zoom in icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.
Please enter a valid email address.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

pop out icon replay 360 icon
horizontal rotate icon

Product Images

Pin and Clip For Class I and II Trailer Hitch Receiver Hitch
Pin and Clip For Class I and II Trailer Hitch Receiver Hitch

Customer Photos


  • Fits 1-1/4 Inch Hitch
  • Standard Hitch Pin
  • 1/2 Inch Diameter
  • Draw-Tite
This grooved, 1/2" diameter pin fits 1-1/4" square receiver hitches. Includes retaining clip. Zinc finish resists corrosion. Call 800-298-8924 to order Draw-Tite hitch pins and clips part number PC2 or order online at etrailer.com. Free expert support on all Draw-Tite products. Guaranteed Lowest Price and Fastest Shipping for Pin and Clip For Class I and II Trailer Hitch Receiver Hitch. Hitch Pins and Clips reviews from real customers.


  • All Info
  • Reviews (83)
  • Q & A (275)
  • Videos (2)
  • Photos
  • Why etrailer?

Draw-Tite Hitch Pins and Clips - PC2

This grooved, 1/2" diameter pin fits 1-1/4" square receiver hitches. Includes retaining clip. Zinc finish resists corrosion.


Features:

  • 1/2" Diameter pin secures ball mounts and accessories to your trailer hitch
  • Pin fits 1-1/4" square receiver hitch
  • Grooved end enables easy clip installation and removal
  • Zinc finish resists corrosion
  • Includes retaining clip
  • 1-Year limited warranty



Product Detail


4666 Draw-Tite Class I and II Pin and Clip - 1/2" Diameter - Zinc

63241 Alternate






Video of Pin and Clip For Class I and II Trailer Hitch Receiver Hitch


Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.




Video Transcript for Draw-Tite Hitch Pins and Clips - Standard Hitch Pin - PC2 Review

Today were going to take a look at the Draw Tite pin and clip, part number PC2. This is a pin and clip set for Class 1 and 2 trailer hitch receivers. It is a -inch diameter pin, and it fits 1 -inch square trailer hitch, and includes the retaining clip as well. Show you how this works. This is a draw bar for a 1 -inch trailer hitch. You would just take the pin, put it right in there, clip that off, and youre good to go.

That should do it for our Draw Tite pin and clip for Class 1 and Class 2 trailer hitch receivers, part number PC2.


Customer Reviews

Pin and Clip For Class I and II Trailer Hitch Receiver Hitch - PC2

Average Customer Rating:  4.8 out of 5 stars   (83 Customer Reviews)

This grooved, 1/2" diameter pin fits 1-1/4" square receiver hitches. Includes retaining clip. Zinc finish resists corrosion.

- PC2

by:


It worked great. Leveled out the trailer perfect. Thanks again for your help, good product, and prompt delivery. 144094


Comments

great

Scott S - 08/04/2015

13898

- PC2

by:


Product fits fine, looks to be of good quality and shipped quickly. My go-to shop for hitch needs 566034



- PC2

by:


Pin secures two hitches together 563672



- PC2

by:


It's a hitch pin...not alot to say about it. It works. eTrailer is a great source for all of your trailering needs. I've ordered before and will again! 551737



- PC2

by:


perfect fit 538795



- PC2

by:


excellent service...fair pricing....quick delivery....I'm a happy camper! 598936



- PC2

by:


Thanks for the great service and quality products. 588932



- PC2

by:


E-Trailer fits like a glove and is so easy to install. Thanks 577186



- PC2

by:


Perfect fit much better than the ones with drilled hole and pin. 520398



- PC2

by:


Excellent service and fast delivery Thanks a bunch! 516069



- PC2

by:


I ordered with the hitch and the thread length was just right. 505211



- PC2

by:


The salesman knew just what I needed 486794



- PC2

by:


Shipping fast and safe. 471253



- PC2

by:


Looks good so far. It’s a Christmas gift so won’t put it together til then but looks nice. It was recommended as one that will fit our odd size hitch receiver so hope it works. 452662



- PC2

by:


Hitch looks good, Haven't used it yet but am sure it will be fine. However, I ordered 2 different sizes of pins. Was supposed to get 1 small pin (1/2") for the 1-1/4"x 1-1/4" part of the hitch and 1 large (5/8") pin for the 2"x 2" part of the hitch. What I got were 2 large (5/8") pins. 446861



- PC2

by:


GOOD PIN ALTHOUGH ANOTHER PIN IN YOUR INVENTORY WAS LESS EXPENSIVE AND WOULD HAVE WORKED JUST AS WELL IF NOT BETTER. 429612



- PC2

by:


I received the order within two days. My son installed the Hitch this past weekend with no problems. Your service was excellent and your sales person was wonderful. He guided me through what I was looking for and answered all my questions with patience. 428941



- PC2

by:


very fast delivery, great product 422356



- PC2

by:


All the parts ordered are of great quality and fit properly. Packaging needs work. The original box was ripped open and had been taped back together by the shipper(UPS). The hitch was still secure but the tow bar was loose and the pin and clip were missing. etrailer sent another pin and clip. In the future possibly adding some fiber tape would lessen the chance of boxes being mangled. 421668



- PC2

by:


On line purchase very helpful, delivery on time, and the product was exactly what I needed. Great first time experience. 421569



- PC2

by:


Okay so instillation was quite simple once I got the wires ran. So I had to remove the rear bumper for instillation of the wires. In the video it made it seem that it would be a quick instillation. 4-5 hours I spent intotal to install. It was about 3 hours with removal of the rear cover. It was so much easier taking off the bumper then trying to feed it like they showed. 421022



- PC2

by:


Instructions were clear and easy to follow box was mangled, but I blame that on the transport all parts were there Yippy 414007



- PC2

by:


Great work ... thanks 410765



- PC2

by:


Everything as advertised. Good quality and very quick shipping. I am very pleased. Thanks 405644



- PC2

by:


Excellent product. Easy to order. Quick delivery. Very satisfied! 399909



- PC2

by:


Does just what I expected. Experience with etrailer was great. Very nice personal touches. 398030



- PC2

by:


Hitch was delivered on time and all the accessories packed in the one box. Will install this weekend. 390467



- PC2

by:


I used this pin to install a 1,5 inch to 2 inch receiver adaptor. Appears to be good quality, didn't rattle and fit snugly. 359059



- PC2

by:


Good. 358759


Comments

Still using it, works well. Thanks for following up.

FC - 03/26/2018

36487

- PC2

by:


great service 347472



- PC2

by:


Product is exactly as advertised. The online video showing dimensions was extremely useful when determining if this was what I needed. Would definitely recommend for similar purchases. 328065



- PC2

by:


The whole reason you shop at etrailer in the first place - great selection, fair price and prompt shipping. It really couldn't be any easier. 322979



- PC2

by:


works great 318636



- PC2

by:


Pin and Clip For Class I and II Trailer Hitch Receiver Hitch - PC2 is the quake and safe easiest way to connect your trailer hitch to your vecicle. 295043


Comments

The pin and clip make installing the hitch easy and safe to use.The pin and clip make installing the hitch easy and safe to use.

David L - 09/15/2017

28218

- PC2

by:


Did not need this product but it came with the hitch. 290220



- PC2

by:


Well made hitch pin.This is the second time I have bought from etrailer.com. both experiences were great.Their service is second to none. 285010



- PC2

by:


Good product 281417



- PC2

by:


Was an excellent choice, both the product and your company. 276956



- PC2

by:


works good 275938



- PC2

by:


High quality and a great price. 265976



- PC2

by:


Works are advertised. 254419


Comments

I havent used the product a lot - couple of time - but it has worked well for me when I do. I will be using it in a few weeks to haul my powerwasher. Thanks for the followupl.

John w - 01/24/2018

33626

- PC2

by:


Perfect fit, clip stay on tight. 243198



- PC2

by:


We're missing but promptly supplied items upon reporting. 238546



- PC2

by:


Same exact part that came with one of the other two products I ordered; I wish I had known that. 229872



- PC2

by:


Etrailer stood by there product and sent me a correction. 226813



- PC2

by:


It's a pin... :) 226675



- PC2

by:


Product as described. Fair price. Quick delivery. 226508



- PC2

by:


Great product. Just what we needed. 221632



- PC2

by:


good quality 210057



- PC2

by:


Product was exactly as advertised and arrived very promptly. 193039


50
83
Show More Reviews

Ask the Experts about this Draw-Tite Hitch Pins and Clips
Do you have a question about this Hitch Pins and Clip?


  • Is There A Motorcycle Carrier That Will Fit A 1-1/4 Inch Trailer Hitch?
  • Since you have a small trail bike that only weighs 112 lbs, you will be able to use a cargo carrier with your hitch and stay within the tongue weight capacity rating of a Class I trailer hitch for a 2014 Kia Soul. This is my recommendation because there is not a motorcyle carrier for Class I trailer hitches due to their tongue capacity rating. I have a similar trail bike to your Coleman ct200u and suggest using the 20x48 Surco Cargo Carrier for 1-1/4" Hitches - Steel - 300 lbs, # 52017....
    view full answer...

  • How to Determine What Size Hitch Pin Required for Trailer
  • You can submit a photo of your trailer or hitch easily enough by using the link and button on our question page. This appears right below the field where you will enter your email address. If you need a standard non-locking hitch pin we offer # PC2 for Class I and Class II hitches. This pin is 1/2-inch in diameter. If you have a Class III, IV or V hitch then instead you can use part # PC3 which is 5/8-inches in diameter. Both include the retaining clip. The linked articles will help...
    view full answer...

  • Availability of Hitch Pin For 2 Inch Trailer Hitch Receiver
  • The two sizes of hitch pins that I carry are 1/2 inch and 5/8 inch. A 2 inch hitch receiver will use the 5/8 inch hitch pin like the Hidden Hitch Pin and Clip, part # PC3. I am including a link to a page of the 5/8 inch hitch pins that I carry. The Class I 1-1/4 inch hitch receivers will use the 1/2 inch hitch pin like the Draw-Tite Pin and Clip, part # PC2. The Softride Replacement Hitch Bolt with Lock Washer, part # SR25879, that you have referenced will only fit the QuietRide stainless...
    view full answer...

  • Can a 2009 Pontiac Vibe Safely Tow a 1,500 Pound Boat Trailer
  • Since you would be right at capacity I do recommend taking any measures feasible in lightening the load. That will make it that much easier on the vehicle. I do believe that properly equipped, the 2009 Pontiac Vibe will be fine towing the 1,500 pounds. Since you will not constantly be towing it up a steep ramp, and that aspect is only a small part of the journey, the Vibe should be just fine. For a trailer hitch, you can use # C12221 but it is for GT models. If you have a GT model then...
    view full answer...

  • Hitch Pin or Lock to Secure a hitch Cover in a Trailer Hitch Receiver
  • A regular hitch pin and clip would work to keep the cover in the hitch. If your trailer hitch is a Class I or II with a 1-1/4 inch wide receiver then you would use pin and clip # PC2. For Class III, IV, and V receivers you would use # PC3. The other option is to go with a lock. For a Class I or II hitch you could use # RH2-XL. For a Class II, IV, or V you can use # RH5-XL. A regular pin or a lock will go through the hitch receiver and through the holes on a hitch cover securing the...
    view full answer...

  • What Hitch is Recommended for the 2010 Kia Soul to Tow a Boat Trailer
  • The three 1-1/4-inch hitches we offer for the 2010 Kia Soul are all Class I-rated and have a tongue weight capacity of 200-lbs. These light-duty hitches are ideal for use with accessory items like bike carriers or for light towing. The link provided will take you to our product page for all three hitches. All require temporary lowering of the exhaust for installation. Your Soul owners manual will indicate if it is rated by the manufacturer for towing a trailer; if so the manual will...
    view full answer...

  • How Complicated is Installation of Curt # C11367 Class I Hitch on 2015 BMW 328d X Drive
  • If you click the provided link, you can see a copy of the installation instructions for the Curt Class I hitch, part # C11367. The installation procedure is pretty extensive. It involves removing the taillights, the rear bumper cover and the rear bumper beam. The hitch is sandwiched between the bumper beam and the vehicle. It is a fairly complicated installation, but the good news is that the only portion of the hitch that will be visible once it's installed is the receiver tube, as you...
    view full answer...

  • What is the Difference Between a Class I and Class II Ball Mount
  • Class I Ball Mounts When towing with a Class I trailer hitch, the Class I ball mount that is recommended by the trailer hitch manufacturer should be used. All Class I trailer hitches are tested and rated with the specific ball mount for that hitch. Using a ball mount that is not recommended by the manufacturer will void the warranty. The features of a a Class I ball mount are: Has a 1-1/4 inch x 1-1/4 inch shank Class II ball mounts will not fit on Class I trailer hitches Held in...
    view full answer...

  • Trailer Hitch Recommendation for a 2012 Honda Accord Crosstour
  • I do have 1 trailer hitch that is listed as a fit for your 2012 Honda Accord Crosstour. Take a look at the Draw-Tite Trailer Hitch # 24852. Draw-Tite does list this hitch as fitting the 2012 models. If you plan on doing some towing, the correct ball mount is # 3590 and you can use pin and clip # PC2. For a ball, use # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter). For trailer wiring use the T-One Vehicle Wiring Harness, # 118500. I have included a link to the installation...
    view full answer...

  • Trailer Hitch for a 2013 Honda Civic SI Sedan
  • I did some digging and found that the Curt trailer hitch # C11391 does fit the 2013 Honda Civic Sedan si model so you can use it. I have included a link to the installation instructions for you. If you will be using the hitch for something like a bike rack or cargo carrier you will need to make sure that the accessory is rated for use on a Class I trailer hitch. Class I trailer hitches are limited to 2 bikes maximum. Curt recommends the use of a stabilization strap, # 18050, for all...
    view full answer...

  • Draw-Tite Hitch Recommendation for Ground Clearance on a 2000 Subaru Outback Wagon
  • Since the CURT Trailer Hitch # C12270 will sit below the rear bumper of your 2000 Subaru Outback Wagon it will reduce the ground clearance on your vehicle. However, the Draw-Tite Trailer Hitch # 36284 will give you a little more ground clearance as the area that goes around the exhaust tip will go above the tip on the Draw-Tite hitch. Whereas, it goes below the tip on the CURT hitch. Check out the picture I attached that shows both of these hitches installed on a similar vehicle as...
    view full answer...

  • Trailer Hitch Recommendation for a 2013 Chevy Sonic Hatchback
  • We do have trailer hitches for the 2013 Chevy Sonic hatchback but # 24876 will not fit. The equivalent hitch that will fit your 2013 is Draw-Tite hitch # 24878. I have included a link to the installation instructions for you. If you plan on doing some towing the correct ball mount is # 3590 and the correct pin and clip is # PC2. For a 1-7/8 inch ball use # 19256 and for a 2 inch use # 19258. For trailer wiring use # 118640. I have linked instructions for the wiring as well.
    view full answer...

  • Will a Draw-Tite Trailer Hitch Fit a 2012 Hyundai Elantra Touring
  • If you have a 2012 Hyundai Elantra Touring Hatchback, the Draw-Tite Trailer Hitch, # 24844, will fit. I have included a link to the installation instructions for you. I have also included a link to all of the hitches that fit the Touring Hatchback model. If you plan on doing some towing, this is a Class I trailer hitch with a 2,000 pound gross trailer weight capacity and 200 pound tongue weight capacity. You will want to consult the vehicle owners manual to determine the towing capacities...
    view full answer...

  • Trailer Hitch Recommendation for a 2010 Ford Fusion Sport with Dual Exhaust
  • Yes, the Draw-Tite Trailer Hitch, # 24865, will fit on all models of the 2010 Ford Fusion including the sport with dual exhaust. This hitch installs exactly the same as Hidden Hitch Trailer Hitch, 60282, which has been discontinued, and we have pictures and a video of it installed on a 2010 Fusion with dual exhaust. I have provided a link to the video for reference. The recommended ball mount but for the Draw-Tite Hitch is # 3594. For a ball you can use # 19256 (1-7/8 inch diameter)...
    view full answer...

  • Replacement Locking Hitch Pin for Subaru Bicycle Rack Made by Yakima
  • Yakima did make the Subaru-branded bike rack but they do not offer any replacement parts directly; these proprietary parts can only be purchased from Subaru. Your Forester could be equipped with either a 1-1/4-inch or a 2-inch hitch receiver. The diameter of the hitch pin will be 1/2-inch for 1-1/4-inch hitches or 5/8-inch for 2-inch hitches. You can measure the size of the receiver opening on your hitch (or the hitch pin hole itself) to determine which size pin you need. If your...
    view full answer...

  • Recommended Trailer Hitch For 2008 Toyota Camry SE V6
  • Yes, we do have a hitch that will fit your 2008 Toyota Camry SE V6, but the item you selected, Curt Trailer Hitch, part # 12343, will not fit the SE model of the Camry. I would recommend the Draw-Tite Trailer Hitch Receiver, part # 36416, which is a Class II 1-1/4 Inch Hitch. To complete your towing setup you may be interested in the following: Draw-Tite Ball Mount, part # 36071 1-7/8 Inch Hitch Ball, part # 19256 2 Inch Hitch Ball, part # 19258 Pin and Clip, part # PC2 T-One Vehicle...
    view full answer...

  • Trailer Hitch and Wiring Recommendations for a 2006 Audi A6 Avant
  • We do have a trailer wiring harness listed for the 2006 Audi A6 Avant. It is the Upgraded Circuit Protected Modulite with 4 Pole Harness, # 119179KIT, that you have referenced. A simple plug and play style connector is not available for your vehicle. I have included a link to the installation instructions and a video showing a typical installation for you. For a trailer hitch, there are several options. The most popular trailer hitch for your vehicle is the Draw-Tite Trailer Hitch, #...
    view full answer...

  • Recommended Cargo Carrier and Hitch that Wont Interfere with Liftgate Sensors of 2014 Ford Escape
  • We have several hitches compatible with your 2014 Escape Titanium. There are Class III hitches with the 2 inch receiver opening, the Draw-Tite # 75758. This hitch will block the hands-free liftgate sensors somewhat, they will only be functional in the areas around the exhaust pipes as shown in the diagram I provided. If you decide to go with a 2 inch hitch, I'd recommend the Curt # C18153 folding cargo carrier. The carrier basket measures 24x60, and the basket can fold up against the...
    view full answer...

  • Trailer Hitch Recommendation for a 2010 Toyota Camry SE with Dual Exhaust
  • The Draw-Tite trailer hitch # 36416, can accommodate a 2010 Toyota Camry with dual exhaust. Take a look at the picture I have included. You can see that the symmetrical design of the hitch leaves enough room for the exhaust on both sides of the vehicle. I have also linked instructions and a video for you. If you plan on doing some towing the correct ball mount is # 36071 and you can use pin and clip # PC2. For a ball use # 19256 for a 1-7/8 inch diameter or # 19258 for a 2 inch diameter....
    view full answer...

  • How Does B&W Trailer Hitch Mount to a 1975 Chevy 1-Ton Dually Pickup Truck
  • On B&W trailer hitch # BWHDRH25122 the mounting brackets are oriented the same for all applications. The tabs point in but attach to the bottoms of the frame rails. The customer submitting photo appears to have some other component installed. The upper brackets in that picture are not part of the hitch assembly. They appear to be bumper brackets. Once installed the receiver should be right under the bottom of the bumper of very close especially since you have a stock bumper on your 1975...
    view full answer...

  • Will Curt Trailer Hitch # 11132 Fit a 2006 Chrysler PT Cruiser Convertible
  • The Curt Trailer Hitch, # C11132, will fit all models of the 2006 Chrysler PT Cruiser which would include your convertible. I have included a link to the instructions for you. If you plan on doing some towing, the correct ball mount is # C45520 and you can use pin and clip # PC2. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring use # 118462. I have linked the instructions and a video showing a typical installation of the wiring.
    view full answer...

  • Trailer Hitch Recommendation for a 1994 Buick Roadmaster Estate Wagon
  • We do have a hitch available for the 1994 Buick Roadmaster Estate Wagon. You can use Draw-Tite trailer hitch, # 36105. Draw-Tite and Hidden Hitch are sister companies. I have included a link to the installation instructions for you to view. The Class III hitches for this vehicle are all obsolete. This hitch is rated for 3,500 pounds gross trailer weight and 300 pounds tongue weight. If the empty weight of the 1972 Airstream is at or near 3,500 pounds, you are likely to be over capacity...
    view full answer...

  • Recommended Hitch for 2015 Volkswagen Jetta 1.8T TDI
  • Curt offers a hitch for the 2015 VW Jetta TDI, the # C11410 Class I. If you're planning on doing some towing, you'll want to consult your owner's manual to determine the actual towing capacity of the vehicle, you'll want to abide by the 2000 lb towing capacity of the hitch or the towing capacity of the vehicle, whichever is lowest. To provide a connection point for the trailer lights, you'll want to install a trailer wiring harness, part # 118572. You can see the installation instructions...
    view full answer...

  • Trailer Hitch Recommendation for a 2011 Volkswagen Golf
  • On all of the trailer hitches available for the 2011 Volkswagen Golf, see link, the cross tube will be visible beneath the rear fascia on the vehicle. There are no hitches from the manufacturers that we carry that are completely hidden from view. The most popular option is # 24825 that you have referenced. I have included a link to the instructions for you. If you plan on doing some towing the correct ball mount is # 3594 and you can use pin and clip # PC2. For a 1-7/8 inch ball use...
    view full answer...

  • Trailer Hitch Recommendation for a 2012 Chevy Cruze LTZ with RS Package
  • This question has come up before and a colleague of mine found out from the manufacturer that the Draw-Tite trailer hitch # 24882 will fit a 2012 Chevy Cruze with the RS package. I have included a link to the installation instructions for you. If you will be doing some towing, the correct ball mount is # 3593 and you can use pin and clip # PC2. For a 1-7/8 inch diameter ball, use # 19256 and for a 2 inch diameter ball use # 19258. For trailer wiring use # 118508. I have included some...
    view full answer...

  • Trailer Hitch Recommendation for a 2013 Volkswagen Golf TDI
  • The Curt trailer hitch, # C11000, has about as much of the crossmember showing but the round tube design fits the overall design of the vehicle, in my opinion, than the other hitch options. I have linked the instructions for you. You can look at some of the customer submitted review photos and judge for yourself. I think it looks pretty good. If you plan on doing some towing the correct ball mount is # C45016. You will also need pin and clip # PC2. Fora 1-7/8 inch ball use # 19256 and...
    view full answer...

  • What Locking Hitch Bolt Will Fit Discontinued Hitch Mounted Yakima Roc 2 Bike Rack
  • The hitch bolt that will fit your Yakima Roc 2 is # Y8890200 providing your hitch has a 2 inch receiver. Your research was correct and this is the replacement for the obsolete bolt (8820052) you found. The Lets Go Aero Hitch Lock # 63232 that you referenced should fit your receiver since you have removed the threaded part of the locking mechanism from inside the bike rack shank. The Yakima # 8890200 is a bit longer than the Aero Lock, however, both will fit a 2 inch receiver. Both bolts...
    view full answer...

  • Will the Draw-Tite # 36416 Fit on a 2011 Toyota Camry SE with Dual Exhaust
  • The Draw-Tite Trailer Hitch, # 36416, will fit on a 2011Toyota Camry with dual exhaust. Take a look at the photo I added for you. You can see that the design of the hitch leaves enough room for the exhaust on both sides of the vehicle. I have also linked instructions and a video for you. At this time there is not a hitch available for the 2011 Toyota Camry SE that does not require bolting to the underside of the spare tire well. If you plan on doing some towing the correct ball mount...
    view full answer...

  • Choosing a Ball Mount For a 1-1/4 Inch Hitch Receiver
  • You mentioned a 1 inch shank size for a ball mount, and the industry standard sizes are 1-1/4 inch, 2 inch, or 2-1/2 inch. The 1-1/4 inch ball mounts come in a variety of rise and drop options to allow you to safely tow a trailer level. I've attached a link for you to see all your options. There aren't adjustable ball mounts for the 1-1/4 inch receivers, so you will have to do some measuring of your tow vehicle, from ground to the inside top edge of your receiver and from the ground...
    view full answer...

  • Will the Pro Series Cargo Carrier # 63155 Fit on a 2013 Subaru Crosstrek With Factory 1-1/4 Hitch
  • You will have no problem inserting the shank of the Pro Series Cargo Carrier, # 63155, into the 1-1/4 inch receiver on your new 2013 Subaru Crosstrek. The important factor to consider when using this cargo carrier on your vehicle is cargo carrier to bumper clearance. To find this clearance, we need to take one simple measurement. You will want to measure from the center of the hitch pin hole on your trailer hitch receiver to the furthest back point on your bumper (see photo). If that...
    view full answer...


Do you have a question about this Hitch Pins and Clip?




  • Why etrailer.com?

    At etrailer.com we guarantee:

  • Highest quality hitch pins and clips for the best price.

    Our Lowest Price Pledge ensures you will never overpay for the parts you need.
  • Real product know-how.

    We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.
  • Most detailed, accurate hitch pins and clip information available.

    Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.
  • Installations, made easy.

    We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.
  • Fast shipping.

    Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.
  • Personalized service for life.

    We provide one-on-one, personalized service from the ordering process through the life of your product.
  • Trusted since 1946.

    We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.
  • Returns Policy

    Satisfaction Guarantee
    Need to return an item? No problem. Please read our Returns Policy for more information.

Info for this part was:

Expert Research:
Michael H
Expert Research:
Jameson C
Video Edited:
Jacob T
Updated by:
Laura H
Video by:
Dustin K
Installed by:
Hayden R
Updated by:
Sarah W

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.



Product Experts Available Now!

Call 800-298-8924


^
About Us
photos and videos
1,056,204

Original Photos & Videos

Produced to make sure you know what you are getting and you get exactly what you need.

installations
35,570

Installations Completed

To make sure products work and fit the way they are supposed to.

etrailer call center
2,476,511

Phone Calls & Emails Answered

1,125,924 phone calls and 1,350,587 emails to help find the right solution.

etrailer training
400+

Average Hours of Product Training

We get to know our products firsthand so experts can better help you.

etrailer service
73

Years of Quality Customer Service

Assisting our neighbors and customers, face to face at the counter.

etrailer experts
193,357

Pages of Expert Information

Created to make sure you have all the answers to your questions, from real experts.