Curt QuickPin No Latch A-Frame Trailer Coupler w/ Jack Hole - 50 Degree - 2-5/16" Ball - 14K

See what our Experts say about this CURT A-Frame Trailer Coupler

• Locking Pin Recommendation for the Curt QuickPin No Latch A-Frame Trailer Coupler
  There is! To replace the standard pin and clip on the Curt QuickPin No Latch A-Frame Trailer Coupler # C84DR Curt actually recommend the Hitch Lock # C23025 which is what I recommend going with!
  view full answer...
• Replacement For 8,000 lb A-Frame Trailer Coupler With 2-5/16 Inch Hitch Ball
  Thanks so much for the photos, and there isn't a replacement for just the front coupler portion of the long-discontinued coupler you have. So in order to switch out from a 2" to a 2-5/16" coupler attachment, you will need to replace the entire coupler. Since yours looks to be bolted on, you can remove it and replace it with another bolt-on coupler that accepts a 2-5/16" hitch ball: - Curt QuickPin No Latch A-Frame Trailer Coupler # C84DR The # C84DR is the easiest way to change your coupler...
  view full answer...
  
• Is There a Trailer Coupler Repair Kit for a 2-5/16" Coupler GVWR 7K
  I do have an option for you and this is a common question but the trailer coupler repairs kits aren't universal and only a very few available for select trailer couplers. Therefore, if you're having issue with your existing coupler it will need to be replaced for which I recommend the Curt QuickPin No Latch A-Frame Trailer Coupler part # C84DR. This is a bolt-on coupler so all you need to do is cut the old one off and drill/bolt the new one in place, no welding required. It also uses a...
  view full answer...
• What Are the Main Differences Between the Curt A20 and S20 Slider
  That's really about it, Frank. They both have the same capacity and are virtually the same. The S20 # C63DR is also a bit quieter than the R20, and automatically latches in both directions so you only have to get out of the truck once.
  view full answer...
• Mounting Hardware Needed To Install Curt QuickPin No Latch A-Frame Trailer Coupler 25474 # C84DR
  The Curt QuickPin No Latch A-Frame Trailer Coupler 25474 # C84DR will require grade 5 hardware. It is recommended to use six 1/2" bolts, six 1/2" lock nuts and twelve 1/2" washers. This can obviously change depending on your exact frame dimensions. I have linked the installation instructions at the bottom of the page which you can show the installer as well.
  view full answer...
• 2 inch Ball Coupler Recommendation for A-Frame Trailer
  I checked with Curt and they only have a 2-5/16 inch ball version of the QuickPin with the part # C84DR. S for a 2 inch ball a-frame coupler I really like the Demco coupler part # DM14793-52 which has the eZ Latch that I think is the easiest and least likely to get hard to operate over time like a lot of couplers do.
  view full answer...
• Availability Of Yakima Lock Cores And Wind Fairings
  Hello John, thanks for reaching out. We do indeed have the Yakima lock cores with keys available. If you are looking for a specific key number, just let me know your key number and we can provide a match. If you need a new lock core and key with any code, the new cores are available in sets of two # Y07202, four # Y07204, six # Y07206, or eight # Y07208. As far as the wind fairing, we do carry those as well. The Yakima fairings are available in the following sizes: - 34" Long # Y05016 -...
  view full answer...
• What Does 50 Degree of Curt QuickPin Coupler # C84DR Reference
  50 degrees in the title and description of the Curt QuickPin part # C84DR is in reference to the angle of the trailer frame that this coupler fits on. This is the standard angle trailer frame so I'd be shocked if your trailer didn't match this.
  view full answer...
• Will Pro Series 6" Detachable Caster Fit Pro Series Round A-Frame Jack
  Yes, the Pro Series 6", Detachable Caster # PS1400750340 will fit the Pro Series Round, A-Frame Jack # PSRV20000103. If you would also like a footplate you can use the # PS1400700340. The only Curt A-Frame coupler we have is the QuickPin # C84DR. This fits a 2-5/16" ball as well with a higher capacity at 14,000 lbs. The QuickPin design allows for a simple and secure hookup. If you would prefer a thumb latch I recommend the A-Frame Trailer Coupler # CA-5400-B instead.
  view full answer...
• Can You Switch a Trailer with Lunette Ring for a 2-5/16" Trailer Coupler
  It sounds like you have a lunette ring on your trailer now and are wanting to swap that out for a 2-5/16" trailer coupler and if that's the case we have some great options for this. If it's an a-frame trailer which is the most common type then I recommend the Curt QuickPin No Latch A-Frame Trailer Coupler part # C84DR which can simply be bolted to the trailer frame with no welding required. In order to remove the old coupler, you'd likely need to cut the existing welds off if that's how...
  view full answer...
• Tekonsha P3 Brake Controller For 2004 Chevy 2500 With Factory Tow Package
  Hello Joseph, thanks for reaching out. The Tekonsha Prodigy P3 Trailer Brake Controller w/ Custom Harness # TK99HR will have everything you need to install the brake controller on your 2004 Chevy Silverado 2500. This includes the custom adapter that makes it directly compatible with the factory tow package on your truck. Since you have the tow package, I assume you already have a 7-way on the back of the truck. If you need one, you can use part # PK11898. This is the only additional part...
  view full answer...

Do you have a question about this A-Frame Trailer Coupler?