Product Experts Available Now!
Call 1-800-940-8924
Replacement Trailer Hub Wheel Stud, Drive-In, 1/2" x 1-13/16" (Qty 4)
(32 reviews)
Price: $16.94
In Stock
Redline
Replacement Trailer Hub Wheel Stud, Drive-In, 1/2" x 1-13/16" (Qty 4)
Part Number: RG03-040
In Stock
$16.94
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (32)
- Q & A (0)
- Videos (1)
- Photos
Redline Accessories and Parts - RG03-040
- Boat Trailer Wheels
- Trailer Hubs and Drums
- Trailer Tires and Wheels
- Wheel Studs
- Drive-In Stud
- 1-13/16 Inch Long
- 1/2 Inch Diameter
- Redline
Replacement Trailer Hub Drive-In Wheel Studs
 | ||||
| Thread Diameter (A) | Stud Length (B) | Spline Length (C) | Base Length (D) | Spline Diameter (E) |
| 1/2" | 1-13/16" | 0.62" | 0.73" | 0.61" |
RG03-040 Replacement Trailer Hub Wheel Stud, Drive-In, 1/2" x 1-13/16" (Qty 4)
Video of Replacement Trailer Hub Wheel Stud, Drive-In, 1/2" x 1-13/16" (Qty 4)
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Hands-On with the Replacement Trailer Hub Wheel Stud, Drive-In, 1/2" x 1-13/16" (Qty 4)
Today we're going to take a look at these replacement drive-in trailer hub wheel studs. It's a 1/2 inch diameter, 1 13/16ths in length and a quantity of four of them. Now these 1/2 inch studs, they're designed to replace damaged wheel studs on your trailer hub. The rate spline portion right here of the stud is going to be driven or pressed into your trailer hub and this stud is what will go through the bolt along your trailer wheel and when it's used with a wheel lug nut it will hold your tire wheel to your axle. They are stamped as Grade A bolts. Again, the thread sized diameter is 1/2 an inch. It's 20 threads per inch and they do use standard 1/2 inch by 20 lug nuts.
Now I did happen to pull one of those 1/2 inch by 20 lug nuts from our warehouse and just to show you after this is installed in your hub, put your wheel up on the stud and then just go ahead and put your lug nut on there and then tighten it down and torque it to the correct specs for your application. Now I do want to give you the overall length. Now the overall length on the studs are always measured from the bottom of the head to the very end. If we put a ruler on this, it's going to be right at 1 13/16ths overall length. The threaded portion length is going to be right at 1 1/4 inches and then the spline diameter, that's the diameter of the spline here, that's the end that gets pressed into the trailer hub, the diameter of that is .61 inches. That should do it for the review of these replacement drive-in trailer hub wheel studs, 1/2 inch diameter by 1 13/16ths length and a quantity of four of them.
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
Ratings & Reviews
4.8
32 reviews
by:
Jason
08/23/2026
These were the exact studs I needed.
by:
Tom G.
03/18/2016
All the products I have ordered from etrailer have arrived quickly and fit perfectly. I would like to say my recent call to customer service was met with a very helpful and polite Ashley E. she took care of my order and my problems. Thank you for the help and the great products. I will definitely be finishing the rest of my projects with the help of your company.
by:
Russell
07/19/2018
Saved my trailer. Someone (me) forgot to tighten the lugnuts after checking the bearings. Destroyed the studs. Could not find them locally anywhere. Found etrailer online, and was able to match the studs just from the pictures and descriptions on the web page. 1-13/16ths was a great clue.. only one. So this old guy thanks you for saving his trusty old trailer.
by:
Leon
05/16/2024
Parts were exactly what I needed, for 1984 W-W flatbed trailer w/electric brakes, wheel studs same as original, fit perfect, adjuster springs same as original. Couldn't be more pleased, fast shipping also.
by:
Rick
11/13/2020
Perfect fit and replacement studs for my 6,000lb axle on my Walton Dump trailer. Always a good experience when ordering from etrailer.com!
by:
Charles
05/07/2016
Needed some press in wheel studs to replace some rotten ones on an old trailer. Wasn't familiar with how many types of press in studs were around. These worked perfectly and were a breeze to install. Thanks!
by:
Scott
03/22/2022
I was not able to use these. The thread cut and stud length are identical to the stud I needed to replace. What I was unaware of is that another variable is the width of the shoulder. These are too fat at the shoulder and would not set into the brake drum. I was able to have the local auto parts store take measurements and get one for me. Nothing wrong with the quality. Just no hint the shoulder was different.
by:
Ron P
09/16/2014
The parts I ordered came in a very timely fashion. You have been a great source of parts allowing me to keep my trailer in good working order at a very reasonable cost. Thanks
by:
Finley
06/16/2018
The person that took my order was very courteous and knowledgeable. Even though this purchase was small, all things were done to see that my order was handled efficiently and arrived on time. It's great to find a company with courteous employees. So far I have seen the product I bought perform well. Thanks!
by:
Roy R.
02/15/2019
Studs and lug nuts arrived on time in good shape and Fit Perfectiy.
by:
Th
09/15/2021
Nice studs but the expanded section that is to be driven in does not fit any of the holes in the PJ branded tire mount.
by:
wayne c
08/25/2016
products received on time and all good shape. All products as described. very happy with this purchase.
by:
Mike
04/26/2018
They worked perfectly for my jet ski trailer
by:
Donald
03/31/2018
Fast shipping and exactly what I needed. Great company.
by:
Jim
02/16/2018
My order came quickly and is exactly what I ordered
by:
Jeff P.
08/26/2014
perfect replacement for a stripped lug.
by:
Jerry
07/07/2015
The product was correct and shipped in a timely manner. It appears to be of good quality and installed easily. Very happy with this product!
by:
David
05/09/2016
Quality products. Great service. Quick del.
by:
Benh
08/04/2021
Did the job!
by:
Shawn
10/12/2019
No issues with install or use.
by:
Herbie
01/28/2019
Every thing worked great.
by:
Ron
05/01/2020
Got the studs very quickly. Steve was the parts guy that got me the right parts. Thanks
by:
Richard
03/28/2020
Excellent Product Great price... Fit perfect on my 2000 Coleman Cheyenne
by:
Scott
08/25/2018
worked well, exact dimensions as shown, Thank you
by:
Tim
12/27/2025
25
32
true
Show More Reviews
See what our Experts say about this Redline Accessories and Parts
- Looking for Wheel Studs for 2016 Crossroads Altitude Toy HaulerHey Brad, there are two options you have but you will need to measure your current studs to be sure: If your existing drive in studs are 1-13/16 inches long (measurement B in picture) you will need the Replacement Trailer Hub Wheel Studs, item # RG03-040. If your existing drive in studs are 2-3/4 inches long (measurement B in picture) you will need the Replacement Trailer Hub Wheel Studs, item # RG03-080. Let me know what dimension you have if you find you have something different.
view full answer... - Replacement 1/2" Trailer Hub Wheel StudHey Mark. I don't have a database that shows me what parts came on your 2016 Keystone High Country. The Provider ST235/80R16 Radial Tire w 16" Viking Aluminum Wheel - 8 on 6-1/2 - LR G - Black item # A16RG8BMMFL80 is the closest option I have to what you described and what's on the brochure for your 5th wheel. If your Keystone Montana has hubs like the Dexter item # 42866UC3-EZ you can replace the studs with item # RG03-040. Do you have a part number or manufacturer off one of your hubs?
view full answer... - Replacement Wheel Stud Part Numbers for the E-Z Lube Hub & Drum Assembly, item # 8-201-5UC3-EZYou would need one of two part numbers to replace the wheel studs in the Complete E-Z Lube Hub & Drum Assembly, item # 8-201-5UC3-EZ. If your existing drive in studs are 1-13/16 inches long (measurement B on the product page) you will need the Replacement Trailer Hub Wheel Studs, item # RG03-040. If your existing drive in studs are 2-3/4 inches long (measurement B on the product page) you will need the Replacement Trailer Hub Wheel Studs, item # RG03-080.
view full answer... - Correct Replacement Wheel Mounting Bolts for a Dexter Hub and Drum Assembly for 3.5K AxlesThe Replacement Mounting Stud for Dexter 5 on 4-1/2 Hub and Drum for Hydraulic Brakes # T0508101 is not going to work with the Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles # 84546UC3-EZ you're looking at as these bolts were meant to replace the bolts on the no longer available Titan 5 on 4-1/2 Hub and Drum T1543900CB042, which uses press in bolts, whereas # 84546UC3-EZ uses drive in bolts. Instead, for the Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles # 84546UC3-EZ you'd...
view full answer... - How to Determine Size of Studs on 2016 Ice Castle TrailerI won't be able to tell you off-hand what size studs you have on your 2016 Ice Castle trailer but I can help you figure out what you have. The reason I can't just tell you, even knowing it's an 8 lug hub, is because 1/2", 5/8", and 9/16" studs are commonly used. What you can do is use a digital caliper like part # PTW80157 and measure the thread diameter of your studs. For example, the Replacement 1/2" x 1-13/16" Trailer Hub Wheel Stud # RG03-040 has a thread diameter of 1/2". I have...
view full answer... - Trailer Hub Stud Recommendation for 5,200 lb Lippert HubI wasn't able to find your specific part number hub but if you have a 5,200 lb hub with a 6 on 5-1/2 inch bolt pattern you are going to need a 1/2 inch drive in stud. If your existing drive in studs are 1-13/16 inches long (measurement B in picture) you will need the Replacement Trailer Hub Wheel Studs, item # RG03-040. If your existing drive in studs are 2-3/4 inches long (measurement B in picture) you will need the Replacement Trailer Hub Wheel Studs, item # RG03-080.
view full answer...
- How to Remove a Stripped Wheel StudIf the studs on your hub are drive-in studs, the most common method for removing the studs is by driving them out with a hammer. If you have a hub with an integrated drum or rotor, I recommend putting the hub flat on the ground before driving out the stud. Most trailer hubs use drive-in studs. If you have screw-in studs, I recommend using a pair of vice grips on the exposed part of the stud and try to unscrew the studs from the hub. If you find the studs to be too difficult to drive...
view full answer... - Can a Wheel That Uses 1/2 Inch Wheel Studs Be Used on a Trailer that Uses 7/16 Inch StudsIn this situation I would actually recommend just replacing the wheel studs themselves. The studs on your current hubs should be able to be knocked out, working at the front side of the hub. That way, you would be able to compare your current studs to ones offered with the 1/2 inch diameter and replace them. You can get a good idea of how the measurements are taken by looking at the diagram on the product page for 1/2 inch wheel stud # RG03-040. I am including a link to all the 1/2...
view full answer... - How do Wheel Studs Typically Get Removed From Trailer HubMost wheel studs are pressed into hubs so what you can do is use a large punch or chisel and a hammer to hammer the broken studs out of the hub and then reverse the process to install new ones.
view full answer... - Replacement Wheel Studs for 2018 Keystone Montana 3721RLSince the 7k hub that fits your 2018 Keystone Montana 3721RL # 42866UC3-EZ uses 1/2 inch wheel studs the replacement studs you'd want is the part # RG03-040 which is 1/2 inch diameter by 1-13/16 inch.
view full answer... - Wheel Stud Solution for Needing Dexter K71-295-00We don't have that exact part number but the Replacement Trailer Hub Wheel Stud # RG03-040 is the same dimensions as that wheel stud so it would work just as well.
view full answer... - Replacement Wheel Studs for 2016 Forest River 381 RBOKFor your 2016 Forest River 381 rbok (since there isn't a 381 BROK) whether it is a Sierra or a Sandpiper model you will want the Replacement Trailer Hub Wheel Stud, Drive-In, 1/2" x 1-13/16" (Qty 4) # RG03-040 based on my research. I've attached a video and a photo to assist.
view full answer...
- Trailer Wheel Stud Recommendation 1/2 inch Diameter 1.85 inches LongThe closest wheel stud we offer to what you need is the part # RG03-040. This has a 1/2 inch thread diameter, .61 spline diameter, overall length of 1.8125 inches. It matches your stud very closely.
view full answer...
- Replacement Wheel Stud Recommendation for a Trailer Hub and Drum Assembly # 8-219-4UC3The replacement studs for your Trailer Hub and Drum Assembly # 8-219-4UC3 that you referenced are 1/2 inch part # RG03-040. All three hubs you referenced will use this as a replacement stud.
view full answer... - Availability of Replacement Trailer Wheel Drive-In StudsIf your trailer is using the Trailer Hub Assembly, # 84545BX, that you have referenced, you can use the Replacement Trailer Hub Wheel Stud, Drive-In, # RG03-040. This is a 1/2 inch drive-in stud that is 1-13/16 inches long with a spline length of 0.62 inches, a base length of 0.73 inches, and a spline diameter of 0.61 inches. These dimensions match those used on the hub you have referenced. If the wheels studs on your hub match these dimensions and are the drive-in style (as opposed to...
view full answer... - What Thread Pitch Does the Replacement Trailer Hub Wheel Stud # RG03-040 HaveI spoke to my contact at Redneck Trailer Supplies to determine the thread pitch for the Replacement Trailer Hub Wheel Stud, Drive-In, 1/2" x 1-13/16" (Qty 4) # RG03-040. He told me the # RG03-040 has the tread pitch of .073, but that it will fit the 1/2 -13 thread pitch you need.
view full answer... - Lug Nuts Torque Setting on Part # 84546UC3-EZLug nuts used on 1/2 inch studs like those on the 84546UC3-EZ Hub and Drum Assembly should be torqued to 75-85 lb/ft.
view full answer... - Fit & Compatibility of Wheel That Uses 1/2 Inch Wheel Studs on a Trailer that Uses 7/16 Inch StudsThe best thing for you to do if you wanted to replace your current split rim wheel with the # AM20514, would be to also replace the wheel studs on your hub. The studs on your current hubs should be able to be knocked out, working at the front side of the hub. That way, you would be able to compare your current studs to ones offered with the 1/2 inch diameter and replace them. You can get a good idea of how the measurements are taken by looking at the diagram on the product page for 1/2...
view full answer... - Do You Have a Wheel Stud that is 1/2" by 1 3/16" for My 1991 Yacht Club Boat Trailer?Hello Jeff, I am kind of hoping that is a typo and you really meant 1-13/16". If so, then you'll want the Replacement Trailer Hub Wheel Stud, Drive-In, 1/2" x 1-13/16" (Qty. 4) # RG03-040. That's a much more common length for a 1/2" wheel stud, which is why I wanted to double-check before pointing you in the right direction. If you really did mean 1-3/16", then I'm sorry, but we don't have anything that matches those dimensions. I even did some digging to see if I could find one from...
view full answer... - Replacement Wheel Studs for Wheels on 2004 Timberlodge by Adventure ManufacturingAll 1/2-inch diameter drive-in wheel studs are shown on the linked page. The one nearest to your required dimensions (thank you for your included photo) is Kodiak # K12WB2. Overall length is slightly greater but most specs match up closely.
view full answer...
- Replacement Wheel Stud Recommendation for a Trailer Hub that Takes Bearings L44643Most likely the studs you would need are the part # RG03-060 which is what the hub part # 8-91-05UC1 takes that has the two bearing numbers you listed. Since I don't know what hub you have for certain though it's hard to be totally sure. The hub I referenced is a very popular option though.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Installed by:
Jeff D
Updated by:
Laura H
Updated by:
Wilson B
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Russell
7/19/2019
Still working perfectly...