Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replacement Trailer Hub Drive-In Wheel Studs
 | ||||
| Thread Diameter (A) | Stud Length (B) | Spline Length (C) | Base Length (D) | Spline Diameter (E) |
| 1/2" | 1-7/8" | 0.26" | 0.52" | 0.54" |
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the replacement drive-in trailer hub wheel studs. These are 1/2" diameter x 1 7/8" in length, and it's for a quantity of four of them. These 1/2" studs are designed to replace damaged wheels studs on your trailer hub, the raise plus flyings portion right here of the stud, is what will be driven or pressed into your trailer hub. The stud is what will go through the bolt hole on your trailer wheel. When it's used with a wheel lug nut, will hold your tire wheel to your axle. The top of the head is stamped, it's a grade A bolt. Again, the thread size end is a 1/2" diameter, 20 threads per inch, and they use standard 1/2" x 20 lug nuts.
I did happen to pull a standard lug nut, 1/2" x 20 from our warehouse just to show you how it screws on. Once this is installed in your trailer hub, put your wheel up on the stud, put your lug nut on, and then just tighten it down and torque it to the correct specs for your application. Few dimensions on these studs. The overall length, which will be measured from the bottom of the head to the very end, and it's going to be right at 1 7/8". The threaded portion, the length on that is going to be right at 1 1/4". The diameter of the spline, that's the portion that gets pressed into your trailer hub, the diameter of that is .54". That should do it for the review on the replacement drive-in trailer hub wheel studs, 1/2" diameter, 1 7/8" in length and a quantity of four of them..
Average Customer Rating: 4.7 out of 5 stars (28 Customer Reviews)
Exactly what I needed, quick shipping and excellent customer service and order status notifications. Thank You
great service!
Perfect fit for my trailer. The folks ate trailer where very helpful. Ordering wheel studs can be difficult to get the size correct and terai lee made it very easy.
Great product and the size chart was spot on. Picture matched the product. My boat trailer is a 2010 Bass Tracker NITRO.
Brought product for a trailer rebuild. Product came as described and seems like great quality. Best part was the customer experience by etrailer, great communication on where my order was and it shipped the same day even though I ordered at about 5pm cst! Will buy from here again.
Perfect fit. No installation problems even with older rusted and broken studs
Very good quality , way better than original with one
Exception , the spline length on these is not very good, but they
Should hold . But in there defense these are not meant for my camper
So there's that, had to grind the heads a tad to fit in hole.
These studs fit my Blizzard sled trailer perfect. I was able to pick them using the dimensions provided. Shipment arrived FAST.
They were an exact fit for my '05 Coachman/Viking pop-up camper.
Great product and great price. thank y ou.
Got just what I ordered..
Har
4/28/2022
Works as should. Good fit and no issues
Perfect fit. Fast delivery and excellent customer service.
Excellent product, it was not a 100% match to my old ones but they were very close and worked well with no issues.
packaging does not line up with needs. Should be packaged in set of 5.
Sized a bit longer than needed, but worked fine.
everything was good
Right size. The sizing charts helped a lot. Can't guess on these. Too many sizes.
Just what I needed
Fit perfectly
They fit!
Shipping was fast.
good value
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Rick
5/6/2019
All still good. Thanks again.