bing tracking image
Q & A Icon

Recommended Anti-Rattle for Curt Cargo Carrier  

Updated 07/29/2026 | Published 07/21/2026

Question:

Plan to purchase rear end carrier. The aluminum version. Please recommend an anti rattle hitch device. Mine is 2 inch. One review mentioned a Thule offset hitch device. What is that. Does it position the rack further from the bumper? Thank you !

0

Expert Reply:

Hey Oren! For an anti-rattle to pair with the Curt Cargo Carrier # C18113 I recommend our own etrailer Anti-Rattle Hitch Collar # e38FV. This can remain on the receiver so you don't have to install it every time you're using the cargo carrier. I also recommend adding a locking hitch pin like # e98882 to keep it secure.

I'm not sure what the Thule offset is that you're referencing. If it was any kind of adapter, that would reduce the capacity of your hitch by 50% which would likely hinder what you can carry on the cargo carrier so I don't recommend it unless you have a clearance issue.

What will you be using this for?

expert reply by:
0
Robin H
etrailer Anti-Rattle Hitch Collar
etrailer Anti-Rattle Hitch Collar
(click to enlarge)
Nicks profile picture

Nicks

7/28/2026

I purchased the Curt aluminum cargo carrier to use on the back of our travel trailer so that we can carry a very light, but bulky, item with us. The e-trailer anti-rattle hitch adapter was used to stabilize the Curt carrier to the receiver on our Grand Design trailer. The anti-rattle hitch adapter is well suited to the job, fits nicely over the existing receiver and can be mounted / removed with just an allen wrench. My only comment is that there are two modest sized allen head machine screws (maybe about #10 ) that hold the adapter in place. They should be stainless screws. I am thinking that should it be left on for a long time, it may make removal problematical when they rust.

Robin H. profile picture
Etrailer Expert

Robin H.

7/28/2026

@Nicks glad to hear it worked well for you. That is definitely a good suggestion, thanks for the feedback and sharing your experience! We're always looking to improve our products so I'll pass that along.
Brent profile picture

Brent

7/28/2026

@Nicks I purchased the anti-hitch-rattle device from etrailer and it works great. I can leave it installed and still swap hitch devices without removing it. This was a game changer for me. I’m thinking about ordering a second one for the bus to lock in the Blue Ox and the flag pole.
Richard D. profile picture

Richard D.

7/28/2026

We just returned from a 5,100-mile trip through the Canadian Maritimes Provinces. We were pulling our EV Smart car. The anti-rattle hitch was easy to install and clearly did its job. Glad I got it. 5stars

Robin H. profile picture
Etrailer Expert

Robin H.

7/28/2026

@RichardD that is a true test right there. Glad to hear it held up and worked well for your setup!
Larry J. profile picture

Larry J.

7/28/2026

I purchased the Anti-Rattle Hitch Collar # e38FV for use with a 2" hitch and my Yakima OnRamp LX e-bike carrier for the back of my motor home. This anti-rattle hitch collar has performed perfectly and have been using for a year. Far better then the last collar I had. I am also using the locking hitch pin like # e98882 for anti theft.

Robin H. profile picture
Etrailer Expert

Robin H.

7/28/2026

@LarryJ you definitely want to keep that movement down when the OnRamp LX # Y88DJ is mounted on a motorhome, and that's a great way to do it. Performing perfectly is what we like to hear! Thanks for taking the time to share your experience with it.
Joe profile picture

Joe

7/28/2026

Hi Oren, I purchased the etrailer anti hitch rattle device to use when towing my camper. It is very easy to install, and use and works great with no problems. I use it to tow a 5000 lb trailer with a very heavy anti sway hitch system and it holds it very well without the hitch slamming back and forth, hope this helps.

Doug profile picture

Doug

7/28/2026

I will agree with Nick’s comment as the screws should be SS. I ordered my first AR piece last fall and it corroded pretty bad over the winter here in WI. I also applied AS compound to the threads when I installed it. I ordered another one back in April and so far it is holding up well and definitely does the job of keeping my hitch tight in the receiver. I pull a 19’ DV glass boat. TY, Doug

Robin H. profile picture
Etrailer Expert

Robin H.

7/29/2026

@Doug another vote for stainless, alright then! I would probably pull it off this winter when you aren't towing since you're in Wisconsin. The winters and salt are the enemy of all things metal.

Product Page this Question was Asked From


Q & A Icon

Continue Researching

See More Q&A Expert Answers >>