Towing Setup for 2026 Honda CR-V

Question

Question:

Looking for a class 3 tow hitch, hardware, and electrical harness for a honda crv 4 cylinder gas. Does your unit come with the electrical?

asked by: Colt B

0

Expert Reply:

Hey Colt,

Thanks for your question. For a Class III trailer hitch on your 2026 Honda CR-V, I'd recommend the Curt Trailer Hitch Receiver # C13397. It provides a 2-inch receiver with a 3,500-lb gross trailer weight rating and a 525-lb tongue weight rating. Keep in mind that while the hitch is rated for those capacities, you should always stay within Honda's towing limits for your specific CR-V, as the vehicle's maximum towing capacity may be lower than the hitch's rating. I've also included an installation video showing the #C13397 being installed on a 2026 Honda CR-V.

For trailer wiring, the Curt T-Connector Vehicle Wiring Harness # C56370 is a confirmed fit for both front-wheel-drive and all-wheel-drive models. This is a plug-and-play harness that provides a 4-way flat connector, making it perfect for towing small utility trailers, boat trailers, and other light-duty trailers. One thing to note is that your CR-V requires an additional fuse to activate the factory tow circuit, and that fuse is not included with the wiring harness. Your owner's manual will identify the correct fuse location and required fuse size.

If you'd like to mount the 4-way connector to the hitch, you'll also need the No-Drill Mounting Bracket #C83DR along with the 4-Way Flat Mounting Bracket #C42CR.

If you don't plan to tow very often, another simple option is to leave the connector stored inside the rear cargo area and pull it out through the hatch only when you need it.

Out of curiosity, what are you planning to tow with your CR-V?

expert reply by: Christopher H

0

Charles S.

7/22/2026

I have purchased and installed a number of hitches from E trailer. Everyone has said perfectly and there’s always a video showing the installation process so you can tell how complicated it’s going to be before you buy. When I need a hitch, I don’t even check anywhere else

Christopher H.

7/22/2026

@CharlesS Really appreciate that! That's exactly what we hope for. Glad the hitches have worked well and that the install videos have made the job a little simpler. Thanks for sticking with us over the years—it means a lot that we're your first stop when you need a hitch.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hi Deb! There are quite a few hitches available for your 2025 Honda CR-V Hybrid and I have the 2" receiver options (best size for what you are wanting) listed below with their corresponding weights. Curt Trailer Hitch Receiver - Custom Fit -…

view full answer...

Towing Setup for 2026 Honda CR-V

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching